The mechanical properties of two-dimensional (2D) materials are critical for their applications in functional devices as well as for strain engineering. Here, we report the Young’s modulus and breaking strength of multilayered InSe, an emerging 2D semiconductor of the layered group III chalcogenide. Few-layer InSe flaks were exfoliated from bulk InSe crystal onto Si/SiO 2 substrate with micro-fabricated holes, and indentation tests were carried out using an atomic force microscopy probe. In combination with both continuum analysis and finite element simulation, we measured the Young’s modulus of multilayer 2D InSe (>5 L) to be 101.37 ± 17.93 GPa, much higher than its bulk counterpart, while its breaking strength is determined to be 8.68 GPa, approaching the theoretical limit of 10.1 GPa. Density functional theory calculations were also carried out to explain the insensitivity of Young’s modulus to the layer count. It is found that 2D InSe is softer than most 2D materials, and exhibits breaking strength higher than that of carbon fiber, yet remaining more compliant, making it ideal for flexible electronics applications. The reliability of our method is also validated by measurement of graphene.
The electronic structures of monolayer and bilayer SnSe 2 under pressure were investigated by using first-principles calculations including van der Waals interactions. For monolayer SnSe 2 , the variation of electronic structure under pressure is controlled by pressure-dependent lattice parameters. For bilayer SnSe 2 , the changes in electronic structure under pressure are dominated by intralayer and interlayer atomic interactions. The n -type thermoelectric properties of monolayer and bilayer SnSe 2 under pressure were calculated on the basis of the semi-classical Boltzmann transport theory. It was found that the electrical conductivity of monolayer and bilayer SnSe 2 can be enhanced under pressure, and such dependence can be attributed to the pressure-induced changes of the Se–Sn antibonding states in conduction band. Finally, the doping dependence of power factors of n -type monolayer and bilayer SnSe 2 at three different pressures were estimated, and the results unveiled that thermoelectric performance of n -type monolayer and bilayer SnSe 2 can be improved by applying external pressure. This study benefits to understand the nature of the transport properties for monolayer and bilayer SnSe 2 under pressure, and it offers valuable insight for designing high-performance thermoelectric few-layered SnSe 2 through strain engineering induced by external pressure.
Two-dimensional (2D) van der Waals (vdWs) ferroelectric heterostructures provide a platform to design multifunctional electronic devices. In this Letter, the 2D vdWs ferroelectric α-In2Se3/Cs3Bi2I9 heterostructures were constructed to investigate the appropriate band alignment, effective masses, charge transfer, and polarization switching barriers by employing first-principle calculation. The results show that the polarization reversal of α-In2Se3 engineers band alignment transition from type-II (α-In2Se3-P↑/Cs3Bi2I9) to type-I (α-In2Se3-P↓/Cs3Bi2I9), resulting in an indirect bandgap changing from 0.09 to 0.75 eV. Calculated electron effective masses are isotropic, which is smaller than those of anisotropic hole effective masses. Interfacial charges transfer from Cs3Bi2I9 to α-In2Se3, which can be ascribed to work function difference. By combining non-equilibrium Green's functions, the current–voltage characteristics of α-In2Se3/Cs3Bi2I9 based ferroelectric tunnel junction were investigated, and the current on/off ratio of 103 is resulted by spatial charge carrier separation and recombination. The proposed electron–hole separation transport design strategy provides a comprehensive theoretical support for the development of microelectronic storage devices.
13 February 2020 in Journal of Physics: Condensed Matter
Both 2D perovskite Cs 2 PbI 4 and phosphorus are significant optoelectronic semiconductor materials, the optical-electrical characters between both contact interfaces are interesting topics. In present work, we demonstrate comparative investigation of optoelectronic properties for two kinds of electrical contact interfaces. i.e. Pb–I and Cs–I interfaces with black phosphorus contacts. The carrier transport, charge transferring and optical properties for both cases are investigated by using first principle calculation. Both contact interfaces exhibit type II band alignment with direct band gap. Charge carrier migration from Cs–I interface to black phosphorus is more strong than that of Pb–I interface by considering differential charge density and bader charge between distinct electrical contact interfaces. Besides, electron–hole effective masses of heterojunctions for both cases along different direction are investigated. Optical absorption coefficients of both cases are compared with those of free-standing Cs 2 PbI 4 and black phosphorus in the visible spectrum. We systematically compared advantages and disadvantages of two kinds of contact interfaces for photovoltaic application, and the results reveal interfacial engineering of 2D heterojunction plays a important role in tuning optoelectronic properties.
It is well known that the performance of thermoelectric measured by figure of merit ZT linearly depends on electrical conductivity, while it is quadratic related to the Seebeck coefficient, and the improvement of Seebeck coefficient may reduce electrical conductivity. As a promising thermoelectric material, BiCuOCh (Ch = Se, S) possesses intrinsically low thermal conductivity, and comparing with its p-type counterpart, n-type BiCuOCh has superior electrical conductivity. Thus, a strategy for increasing Seebeck coefficient while almost maintaining electrical conductivity for enhancing thermoelectric properties of n-type BiCuOCh is highly desired. In this work, the effects of uniaxial tensile strain on the electronic structures and thermoelectric properties of n-type BiCuOCh are examined by using first-principles calculations combined with semiclassical Boltzmann transport theory. The results indicate that the Seebeck coefficient can be enhanced under uniaxial tensile strain, and the reduction of electrical conductivity is negligible. The enhancement is attributed to the increase in the slope of total density of states and the effective mass of electron, accompanied with the conduction band near Fermi level flatter along the Γ to Z direction under strain. Comparing with the unstrained counterpart, the power factor can be improved by 54% for n-type BiCuOSe, and 74% for n-type BiCuOS under a strain of 6% at 800 K with electron concentration 3 × 1020 cm−3. Furthermore, the optimal carrier concentrations at different strains are determined. These insights point to an alternative strategy for superior thermoelectric properties.
The regulation of tunneling electroresistance (TER) in two-dimensional (2D) ferroelectric tunnel junctions (FTJs) is crucial for their practical applications. In this Letter, we introduce an innovative approach to manipulate TER by altering the interfacial contact barrier through polarization-induced modifications in interface transport properties. A comprehensive analysis of the electronic structures within heterostructures, consisting of a metallic TaSe2 monolayer and a ferroelectric Sc2CO2 layer, uncovers a dual modulation effect of ferroelectricity on both the Schottky barrier height and the interfacial tunneling barrier. This phenomenon substantiates the influence of polarization on charge carrier transport across the interface. Through calculations employing the non-equilibrium Green's function method, we reveal a significant TER ratio (2.41×1013%) in TaSe2/Sc2CO2-based FTJs. Our findings illustrate that distinct tunneling resistance states can be achieved through polarization reversal, as predicted by the proposed mechanism. These insights enhance the understanding of polarization-mediated TER in 2D FTJs and provide a foundation for the design of next-generation electronic devices leveraging 2D ferroelectric materials.