In the present study, the dissolution and precipitation behaviour of four different aluminium alloys (EN AW-6005A, EN AW-6082, EN AW-6016, and EN AW-6181) in four different initial heat treatment conditions (T4, T6, overaged, and soft annealed) was investigated during heating in a wide dynamic range. Differential scanning calorimetry (DSC) was used to record heating curves between 20 and 600 °C. Heating rates were studied from 0.01 K/s to 5 K/s. We paid particular attention to control baseline stability, generating flat baselines and allowing accurate quantitative evaluation of the resulting DSC curves. As the heating rate increases, the individual dissolution and precipitation reactions shift to higher temperatures. The reactions during heating are significantly superimposed and partially run simultaneously. In addition, precipitation and dissolution reactions are increasingly suppressed as the heating rate increases, whereby exothermic precipitation reactions are suppressed earlier than endothermic dissolution reactions. Integrating the heating curves allowed the enthalpy levels of the different initial microstructural conditions to be quantified. Referring to time–temperature–austenitisation diagrams for steels, continuous heating dissolution diagrams for aluminium alloys were constructed to summarise the results in graphical form. These diagrams may support process optimisation in heat treatment shops.
The conventional clinching of steels is currently limited to tensile strength less than 800 N/mm2 and to elongation at fracture more than 14 %. To realise the clinching of high-strength steels, the sheet can be heated locally at the joint, to improve ductility. Thereby the material characteristics outside the joint should be maintained. This could be achieved by means of short-time laser heating. The short-time tempering behaviour of press hardened steel 22MnB5 has been analysed. The mechanical properties during a short-time heat treatment were investigated by thermo-mechanical analysis in a deformation dilatometer. Thereby laser-assisted clinching shall be established and an efficient form-closed and force-closed connection shall be produced. As a result, the press hardened steel 22MnB5 could be clinched by laser assistance for the very first time.
The mechanical properties after age hardening heat treatment and the kinetics of related phase transformations of high strength AlZnMgCu alloy AA 7068 were investigated. The experimental work includes differential scanning calorimetry (DSC), differential fast scanning calorimetry (DFSC), sophisticated differential dilatometry (DIL), scanning electron microscopy (SEM), as well as hardness and tensile tests. For the kinetic analysis of quench induced precipitation by dilatometry new metrological methods and evaluation procedures were established. Using DSC, dissolution behaviour during heating to solution annealing temperature was investigated. These experiments allowed for identification of the appropriate temperature and duration for the solution heat treatment. Continuous cooling experiments in DSC, DFSC, and DIL determined the kinetics of quench induced precipitation. DSC and DIL revealed several overlapping precipitation reactions. The critical cooling rate for a complete supersaturation of the solid solution has been identified to be 600 to 800 K/s. At slightly subcritical cooling rates quench induced precipitation results in a direct hardening effect resulting in a technological critical cooling rate of about 100 K/s, i.e., the hardness after ageing reaches a saturation level for cooling rates faster than 100 K/s. Maximum yield strength of above 600 MPa and tensile strength of up to 650 MPa were attained.
Quenching is an important step during age hardening of aluminium alloys. It significantly influences on microstructures, properties, residual stresses and component distortion. Due to high heat transfer, thermal stresses occur in quenched components. I.e., all premature precipitates during undercritical quenching form on condition of mechanical stresses. Opposite, quench sensitivity investigations, e.g. recording of continuous cooling precipitation diagrams, are usually performed in stress-free conditions and may therefore be incomplete. We have developed a new method of thermomechanical analysis and calorimetric reheating to investigate stress induced precipitation during quenching of aluminium alloys. For aluminium alloy 2024, it has been shown for the very first time that mechanical stresses during quenching also influence on quench-induced precipitation reactions.
1 August 2023 in HTM Journal of Heat Treatment and Materials
As an additive manufacturing process, powder bed fusion of metals using a laser beam (PBF-LB/M) enables the near-net-shape production of complex components in a single step. In combination with case hardening, it will thus be possible in the future to produce lightweight, functionally integrated transmission components characterized by high-strength surface layers with a sufficiently tough component core. However, the process-related new initial conditions resulting from very high solidification rates in PBF-LB/M may mean that case hardening of PBF-LB/M materials with standard parameters achieves different case hardening results than have been usual in the past. This hypothesis was investigated in the present work using the case hardening steel 20MnCr5 (material number 1.7147) after successful development of industry-relevant PBF-LB/M parameters. Besides the convincing results regarding microstructure, hardness and carbon depth profiles, case hardening with standard parameters led to irregular grain growth due to holding at high temperatures for several hours during carburization.