Chengwei Fan

Dr. Chengwei Fan


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 January 2020 in Journal of Vibration Engineering & Technologies
Verified
Journal Article
Closed access
PDF file
CFChengwei Fan
Chengwei Fan
Yadong WuYadong Wu
Yadong Wu
PRPete Russhard
Pete Russhard
AWAnjenq Wang
Anjenq Wang

28 December 2020 in Journal of Turbomachinery
Verified
Journal Article
Closed access
PDF file
RARichard Amankwa Adjei
Richard Amankwa Adjei
CFChengwei Fan
Chengwei Fan
WWWeiZhe Wang
WeiZhe Wang
YLYingzheng Liu
Yingzheng Liu

1 September 2021 in Transactions of the Canadian Society for Mechanical Engineering
Verified
Journal Article
Closed access
CFChengwei Fan
Chengwei Fan
Yadong WuYadong Wu
Yadong Wu
PRPeter Russhard
Peter Russhard
CRCan Ruan
Can Ruan
AWAnjenq Wang
Anjenq Wang
The blade vibration measurement is crucial for gas turbine engines to ensure safe operations. One of the techniques is blade tip-timing (BTT), which is under the assumption that rotor speed is constant and depends on a once-per-revolution (OPR) timing reference to calculate the blade tip displacement and to identify the blade sequence. However, this assumption is incorrect for transient conditions, and the installation of an OPR sensor sometimes is not allowable and reliable. These reasons greatly limit the application of the BTT technique. This paper proposes a self-correcting (SC)-BTT method to realize the blade vibration measurement under different operating conditions without the use of an OPR sensor. The proposed method is based on polynomial fitting, and a reference probe is used to correct high-order fitting coefficients. Numerical results show that the SC-BTT method can greatly reduce the fitting error caused by blade pitch and vibrational parameters. Experimental results demonstrate that the proposed method is capable of removing the limitation of the lack of an OPR sensor and overcoming the drawbacks of the OPR system, such as the failure of the OPR sensor or low-speed resolution. For three investigated cases, the relative errors of derived rotor speed are below 0.12%. The relative error of blade peak-to-peak amplitude (PPA) and initial phase angle are around 3% at the resonance region with engine order (EO) 2.

24 December 2018 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
CFChengwei Fan
Chengwei Fan
PRP Russhard
P Russhard
AWA Wang
A Wang
YCY Chen
Y Chen
WDW Dong
W Dong
Blade tip timing (BTT) as an alternative method is capable of directly measuring the blade tip displacement and inferring the vibration characteristics of rotating blades. Its use is growing in popularity due to its ease of application and the ability to deliver information concerning all blades in a rotor. Although the interpretation of the collected data remains an issue, this paper puts forward a process of using such data to analyse the vibrational characteristics of fan blades under different operating conditions and find the blade endurance margin combined with finite element analysis (FEA). A test system with eight casing-mounted optical probes and one OPR (once per revolution) sensor is built to collect the blades' arrival time of an axial fan. Results indicate that flutter occurs at engine order (EO) 1.5 with a combination of three nodal diameters (2, 3, 4), however, nodal diameter 2 is dominant. A noticeable response (EO≈0.5) is considered as stall. Because every blade vibrates with a frequency lower than its natural frequency (eigenfrequency), and all of them undergo a similar vibration form, continuously rising and falling, which caused by the rotating stall cells. The 1st flex mode-EO2 crossing is found at 48% rotor speed and it's consistent with the results of FEA. Finally, the blade endurance in Goodman diagram demonstrates that flutter poses a higher risk in comparison with the synchronous vibration.