In order to meet the requirement of high sensitivity and signal-to-noise ratios (SNR), this study develops and optimizes a piezoresistive pressure sensor by using double silicon nanowire (SiNW) as the piezoresistive sensing element. First of all, ANSYS finite element method and voltage noise models are adopted to optimize the sensor size and the sensor output (such as sensitivity, voltage noise and SNR). As a result, the sensor of the released double SiNW has 1.2 times more sensitivity than that of single SiNW sensor, which is consistent with the experimental result. Our result also displays that both the sensitivity and SNR are closely related to the geometry parameters of SiNW and its doping concentration. To achieve high performance, a p-type implantation of 5 × 1018 cm−3 and geometry of 10 µm long SiNW piezoresistor of 1400 nm × 100 nm cross area and 6 µm thick diaphragm of 200 µm × 200 µm are required. Then, the proposed SiNW pressure sensor is fabricated by using the standard complementary metal-oxide-semiconductor (CMOS) lithography process as well as wet-etch release process. This SiNW pressure sensor produces a change in the voltage output when the external pressure is applied. The involved experimental results show that the pressure sensor has a high sensitivity of 495 mV/V·MPa in the range of 0–100 kPa. Nevertheless, the performance of the pressure sensor is influenced by the temperature drift. Finally, for the sake of obtaining accurate and complete information over wide temperature and pressure ranges, the data fusion technique is proposed based on the back-propagation (BP) neural network, which is improved by the particle swarm optimization (PSO) algorithm. The particle swarm optimization–back-propagation (PSO–BP) model is implemented in hardware using a 32-bit STMicroelectronics (STM32) microcontroller. The results of calibration and test experiments clearly prove that the PSO–BP neural network can be effectively applied to minimize sensor errors derived from temperature drift.
To meet the radiosonde requirement of high sensitivity and linearity, this study designs and implements a monolithically integrated array-type piezoresistive intelligent pressure sensor system which is made up of two groups of four pressure sensors with the pressure range of 0–50 kPa and 0–100 kPa respectively. First, theoretical models and ANSYS (version 14.5, Canonsburg, PA, USA) finite element method (FEM) are adopted to optimize the parameters of array sensor structure. Combing with FEM stress distribution results, the size and material characteristics of the array-type sensor are determined according to the analysis of the sensitivity and the ratio of signal to noise (SNR). Based on the optimized parameters, the manufacture and packaging of array-type sensor chips are then realized by using the standard complementary metal-oxide-semiconductor (CMOS) and microelectromechanical system (MEMS) process. Furthermore, an intelligent acquisition and processing system for pressure and temperature signals is achieved. The S3C2440A microprocessor (Samsung, Seoul, Korea) is regarded as the core part which can be applied to collect and process data. In particular, digital signal storage, display and transmission are realized by the application of a graphical user interface (GUI) written in QT/E. Besides, for the sake of compensating the temperature drift and nonlinear error, the data fusion technique is proposed based on a wavelet neural network improved by genetic algorithm (GA-WNN) for average measuring signal. The GA-WNN model is implemented in hardware by using a S3C2440A microprocessor. Finally, the results of calibration and test experiments achieved with the temperature ranges from −20 to 20 °C show that: (1) the nonlinear error and the sensitivity of the array-type pressure sensor are 8330 × 10−4 and 0.052 mV/V/kPa in the range of 0–50 kPa, respectively; (2) the nonlinear error and the sensitivity are 8129 × 10−4 and 0.020 mV/V/kPa in the range of 50–100 kPa, respectively; (3) the overall error of the intelligent pressure sensor system is maintained at ±0.252% within the hybrid composite range (0–100 kPa). The involved results indicate that the developed array-type composite pressure sensor has good performance, which can provide a useful reference for the development of multi-range MEMS piezoresistive pressure sensor.
16 November 2021 in Journal of Micromechanics and Microengineering
The pressure and temperature inside the tire is mainly monitored by the tire pressure monitoring system (TPMS). In order to improve the integration of the TPMS system, moreover enhance the sensitivity and temperature-insensitivity of pressure measurement, this paper proposes a microelectromechanical (MEMS) chip-level sensor based on stress-sensitive aluminum–silicon hybrid structures with amplified piezoresistive effect and temperature-dependent aluminum–silicon hybrid structures for hardware and software temperature compensations. Two types of aluminum–silicon hybrid structures are located inside and outside the strained membrane to simultaneously realize the measurement of pressure and temperature. The model of this composite sensor chip is firstly designed and verified for its effectiveness by using finite element numerical simulation, and then it is fabricated based on the standard MEMS process. The experiments indicate that the pressure sensitivity of the sensor is between 0.126 mV/(V·kPa) and 0.151 mV/(V·kPa) during the ambient temperature ranges from −20 °C to 100 °C, while the measurement error, sensitivity and temperature coefficient of temperature-dependent hybrid structures are individually ±0.91 °C, −1.225 mV/(V °C) and −0.150% °C −1 . The thermal coefficient of offset (TCO) of pressure measurement can be reduced from −3.553%FS °C −1 to −0.375%FS °C −1 based on the differential output of the proposed sensor. In order to obtain the better performance of temperature compensation, Elman neural network based on ant colony algorithm is applied in the data fusion of differential output to further eliminate the temperature drift error. Based on which, the overall measured error is within 3.45 kPa, which is less than ±1.15%FS. The TCO is −0.017%FS °C −1 , and the thermal coefficient of span is −0.020%FS °C −1 . The research results may provide a useful reference for the development of the high-performance MEMS composite sensor for the TPMS system.
This paper provides a novel and effective compensation method by improving the hardware design and software algorithm to achieve optimization of piezoresistive pressure sensors and corresponding measurement systems in order to measure pressure more accurately and stably, as well as to meet the application requirements of the meteorological industry. Specifically, GE NovaSensor MEMS piezoresistive pressure sensors within a thousandth of accuracy are selected to constitute an array. In the versatile compensation method, the hardware utilizes the array of MEMS pressure sensors to reduce random error caused by sensor creep, and the software adopts the data fusion technique based on the wavelet neural network (WNN) which is improved by genetic algorithm (GA) to analyze the data of sensors for the sake of obtaining accurate and complete information over the wide temperature and pressure ranges. The GA-WNN model is implemented in hardware by using the 32-bit STMicroelectronics (STM32) microcontroller combined with an embedded real-time operating system µC/OS-II to make the output of the array of MEMS sensors be a direct digital readout. The results of calibration and test experiments clearly show that the GA-WNN technique can be effectively applied to minimize the sensor errors due to the temperature drift, the hysteresis effect and the long-term drift because of aging and environmental changes. The maximum error of the low cost piezoresistive MEMS-array pressure transmitter proposed by us is within 0.04% of its full-scale value, and it can satisfy the meteorological pressure measurement.
In order to meet the requirements for high sensitivity and low temperature drift of pressure sensors in the field of meteorological detection or tire pressure monitoring system (TPMS), this paper proposes a MEMS chip-level pressure sensor based on two pairs of aluminum-silicon hybrid structures, which are etched on the SOI wafer. The pressure sensor achieves the amplified piezoresistive effect by the micron thick ohmic contact between the boron-doped silicon and external aluminum shunt, as verified by finite element numerical simulation and experiment. Four symmetrical L-shaped raised structures are distributed around the square strained membrane, which enhance the stress of the pair of stress-sensitive aluminum-silicon hybrid structures. The other pair of hybrid structures placed outside the strained membrane of the sensor chip enables differential sensor output which is highly insensitive to temperature. The offset drift of differential output is reduced to -4.39%FS compared with that of single aluminum-silicon hybrid structure. Cooperated with temperature compensation structures, an additional thermodynamic control system by using PID algorithm to keep the working temperature stable can eliminate the temperature drift of sensor output. The feasibility of the thermodynamic control system is verified by steady-state thermal simulation. Experiment test results show that the sensitivity of a single aluminum-silicon hybrid structure can reach 0.283 mV/V/kPa at constant heating temperature of 50 °C, and whose thermal coefficient of offset (TCO) can be reduced from -6.92E-1 to -1.51E-3 %FS/°C in ambient temperature ranges of -20 to 50 °C.