Abdulmajeed Dabwan

Mr. Abdulmajeed Dabwan

Industrial Engineering Department, College of Engineering, King Saud University, Riyadh 11421, Saudi

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 August 2019 in PLOS ONE
Verified
Journal Article
Open access
PDF file
AAAli M Alsamhan
Ali M Alsamhan
ARAdham E Ragab
Adham E Ragab
ADAbdulmajeed Dabwan
Abdulmajeed Dabwan
MNMustafa M. Nasr
Mustafa M. Nasr
LHLotfi Hidri
Lotfi Hidri
Single-point incremental forming (SPIF) is a technology that allows incremental manufacturing of complex parts from a flat sheet using simple tools; further, this technology is flexible and economical. Measuring the forming force using this technology helps in preventing failures, determining the optimal processes, and implementing on-line control. In this paper, an experimental study using SPIF is described. This study focuses on the influence of four different process parameters, namely, step size, tool diameter, sheet thickness, and feed rate, on the maximum forming force. For an efficient force predictive model based on an adaptive neuro-fuzzy inference system (ANFIS), an artificial neural network (ANN) and a regressions model were applied. The predicted forces exhibited relatively good agreement with the experimental results. The results indicate that the performance of the ANFIS model realizes the full potential of the ANN model.

8 January 2020 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
ADAbdulmajeed Dabwan
Abdulmajeed Dabwan
Adham RagabAdham Ragab
Adham Ragab
MSMohamed A. Saleh
Mohamed A. Saleh
SASaqib Anwar
Saqib Anwar
AGAtef M. Ghaleb
Atef M. Ghaleb
ARAteekh Ur Rehman
Ateekh Ur Rehman
Single‐point incremental forming is an innovative flexible and inexpensive technique to form sheet products when prototypes or small batches are required. The process allows complex geometries to be produced using a computer numerical control machine, eliminating the need for a special die. This study reports on the effects of four important single‐point incremental forming process parameters on produced surface profile accuracies. The profile accuracy was estimated by measuring the side angle errors and surface roughness and also waviness and circularity of the product inner surface. Full factorial design of experiments was used to plan the study, and the analysis of variance was used to analyze and interpret the results. The results indicate that the tool diameter (d), step depth (s), and sheet thickness (t) have significant effects on the produced profile accuracy, while the feed rate (f) is not significant. As a general rule, thin sheets with greater tool diameters yielded the best surface quality. The results also show that controlling all surface quality features is complex because of the contradicting effects of, and interactions between, a number of the process parameters.

5 April 2021 in Materials
Verified
Journal Article
Open access
PDF file
ADAbdulmajeed Dabwan
Abdulmajeed Dabwan
SASaqib Anwar
Saqib Anwar
AAAli M Alsamhan
Ali M Alsamhan
Abdullah Yahia AlFaifyAbdullah Yahia AlFaify
Abdullah Yahia AlFaify
MNMustafa M. Nasr
Mustafa M. Nasr
Laser-powder bed fusion (L-PBF) process is a family of modern technologies, in which functional, complex (3D) parts are formed by selectively melting the metallic powders layer-by-layer based on fusion. The machining of L-PBF parts for improving their quality is a difficult task. This is because different component orientations (L-PBF-layer orientations) produce different quality of machined surface even though the same cutting parameters are applied. In this paper, stainless steel grade SS 316L parts from L-PBF were subjected to the finishing (milling) process to study the effect of part orientations. Furthermore, an attempt is made to suppress the part orientation effect by changing the layer thickness (LT) of the parts during the L-PBF process. L-PBF parts were fabricated with four different layer thicknesses of 30, 60, 80 and 100 μm to see the effect of the LT on the finish milling process. The results showed that the layer thickness of 60 μm has significantly suppressed the part orientation effect as compared to the other three-layer thicknesses of 30, 80 and 100 μm. The milling results showed that the three-layer thickness including 30, 80 and 100 μm presented up to a 34% difference in surface roughness among different part orientations while using the same milling parameters. In contrast, the layer thickness of 60 μm showed uniform surface roughness for the three-part orientations having a variation of 5–17%. Similarly, the three-layer thicknesses 30, 80 and 100 μm showed up to a 25%, 34% and 56% difference of axial force (Fa), feed force (Ff) and radial force (Fr), respectively. On the other hand, the part produced with layer thickness 60 μm showed up to 11%, 25% and 28% difference in cutting force components Fa, Ff and Fr, respectively. The three-layer thicknesses 30, 80 and 100 μm in micro-hardness were found to vary by up to 14.7% for the three-part orientation. Negligible micro-hardness differences of 1.7% were revealed by the parts with LT 60 μm across different part orientations as compared to 6.5–14% variations for the parts with layer thickness of 30, 80 and 100 μm. Moreover, the parts with LT 60 μm showed uniform and superior surface morphology and reduced edge chipping across all the part orientations. This study revealed that the effect of part orientation during milling becomes minimum and improved machined surface integrity is achieved if the L-PBF parts are fabricated with a layer thickness of 60 μm.

14 December 2020 in Materials
Verified
Journal Article
Open access
PDF file
MNMustafa M. Nasr
Mustafa M. Nasr
SASaqib Anwar
Saqib Anwar
AAAli M Alsamhan
Ali M Alsamhan
MGMageed Ghaleb
Mageed Ghaleb
ADAbdulmajeed Dabwan
Abdulmajeed Dabwan
The studies about the effect of the graphene reinforcement ratio and machining parameters to improve the machining performance of Ti6Al4V alloy are still rare and incomplete to meet the Industry 4.0 manufacturing criteria. In this study, a hybrid adaptive neuro-fuzzy inference system (ANFIS) with a multi-objective particle swarm optimization method is developed to obtain the optimal combination of milling parameters and reinforcement ratio that lead to minimize the feed force, depth force, and surface roughness. For achieving this, Ti6Al4V matrix nanocomposites reinforced with 0 wt.%, 0.6 wt.%, and 1.2 wt.% graphene nanoplatelets (GNPs) are produced. Afterward, a full factorial approach was used to design experiments to investigate the effect of cutting speed, feed rate, and graphene nanoplatelets ratio on machining behaviour. After that, artificial intelligence based on ANFIS is used to develop prediction models as the fitness function of the multi-objective particle swarm optimization method. The experimental results showed that the developed models can obtain an accurate estimation of depth force, feed force, and surface roughness with a mean absolute percentage error of 3.87%, 8.56%, and 2.21%, respectively, as compared with experimentally measured outputs. In addition, the developed artificial intelligence models showed 361.24%, 35.05%, and 276.47% less errors for depth force, feed force, and surface roughness, respectively, as compared with the traditional mathematical models. The multi-objective optimization results from the new approach indicated that a cutting speed of 62 m/min, feed rate of 139 mm/min, and GNPs reinforcement ratio of 1.145 wt.% lead to the improved machining characteristics of GNPs reinforced Ti6Al4V matrix nanocomposites. Henceforth, the hybrid method as a novel artificial intelligent method can be used for optimizing the machining processes with complex relationships between the output responses.

25 August 2023 in Journal of Engineering Research
Verified
Journal Article
Open access
ARAdham E. Ragab
Adham E. Ragab
AAAbdulrahman Alsaty
Abdulrahman Alsaty
AAAli Alsamhan
Ali Alsamhan
AAAbdulsalam Abdulaziz Al-Tamimi
Abdulsalam Abdulaziz Al-Tamimi
ADAbdulmajeed Dabwan
Abdulmajeed Dabwan
WAWaleed Alghilan
Waleed Alghilan

1 September 2020 in Metals
Verified
Journal Article
Open access
PDF file
ADAbdulmajeed Dabwan
Abdulmajeed Dabwan
SASaqib Anwar
Saqib Anwar
AAAli M Alsamhan
Ali M Alsamhan
MNMustafa M. Nasr
Mustafa M. Nasr
The machining of the electron beam melting (EBM) produced parts is a challenging task because, upon machining, different part orientations (EBM layers’ orientations) produce different surface quality even when the same machining parameters are employed. In this paper, the EBM fabricated parts are machined in three possible orientations with regard to the tool feed direction, where the three orientations are “tool movement in a layer plane” (TILP), “tool movement perpendicular to layer planes” (TLP), and “tool movement parallel to layers planes” (TPLP). The influence of the feed rate, radial depth of cut, and cutting speed is studied on surface roughness, cutting force, micro-hardness, microstructure, chip morphology, and surface morphology of Ti6Al4V, while considering the EBM part orientations. It was found that different orientations have different effects on the machined surface during milling. The results show that the EBM parts can achieve good surface quality and surface integrity when milled along the TLP orientation. For instance, surface roughness (Sa) can be improved up to 29% when the milling tool is fed along the TLP orientation compared to the other orientations (TILP and TPLP). Furthermore, surface morphology significantly improves with lower micro-pits, redeposited chips, and feed marks in case of the TLP orientation.