Ahmed Hassen

Dr. Ahmed Hassen

Oak Ridge National Laboratory

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 April 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Hossein TaheriHossein Taheri
Hossein Taheri
AHAhmed Hassen
Ahmed Hassen
Carbon- and glass fiber-reinforced polymer (CFRP and GFRP) composite materials have been used in many industries such as aerospace and automobile because of their outstanding strength-to-weight ratio and corrosion resistance. The quality of these materials is important for safe operation. Nondestructive testing (NDT) techniques are an effective way to inspect these composites. While ultrasonic NDT has previously been used for inspection of composites, conventional ultrasonic NDT, using single element transducers, has limitations such as high attenuation and low signal-to-noise ratio (SNR). Using phased array ultrasonic testing (PAUT) techniques, signals can be generated at desired distances and angles. These capabilities provide promising results for composites where the anisotropic structure makes signal evaluation challenging. Defect detection in composites based on bulk and guided waves are studied. The capability of the PAUT and its sensitivity to flaws were evaluated by comparing the signal characteristics to the conventional method. The results show that flaw sizes as small as 0.8 mm with penetration depth up to 25 mm can be detected using PAUT, and the result signals have better characteristics than the conventional ultrasonic technique. In addition, it has been shown that guided wave generated by PAUT also has outstanding capability of flaw detection in composite materials.

1 July 2016 in Composites Part B: Engineering
Verified
Journal Article
Closed access
AHAhmed Hassen
Ahmed Hassen
Hossein TaheriHossein Taheri
Hossein Taheri
UVUday K. Vaidya
Uday K. Vaidya

26 July 2020 in Materials
Verified
Journal Article
Open access
PDF file
Mariappan Parans ParanthamanMariappan Parans Paranthaman
Mariappan Parans Paranthaman
VOLKAN YILDIRIMVOLKAN YILDIRIM
VOLKAN YILDIRIM
TLTej Nath Lamichhane
Tej Nath Lamichhane
BBBenjamin A. Begley
Benjamin A. Begley
BPBrian K. Post
Brian K. Post
INIkenna Nlebedim
Ikenna Nlebedim
Extrusion based additive manufacturing of polymer composite magnets can increase the solid loading volume fraction with greater mechanical force through the printing nozzle as compared to traditional injection molding process. About 63 vol% of isotropic NdFeB magnet powders were compounded with 37 vol% of polyphenylene sulfide and bonded permanent magnets were fabricated while using Big Area Additive Manufacturing without any degradation in magnetic properties. The polyphenylene sulfide bonded magnets have a tensile stress of 20 MPa, almost double than that of nylon bonded permanent magnets. Additively manufactured and surface-protective-resin coated bonded magnets meet the industrial stability criterion of up to 175 °C with a flux-loss of 2.35% over 1000 h. They also exhibit better corrosion resistance behavior when exposed to acidic (pH = 1.35) solution for 24 h and also annealed at 80 °C over 100 h (at 95% relative humidity) over without coated magnets. Thus, polyphenylene sulfide bonded, additively manufactured, protective resin coated bonded permanent magnets provide better thermal, mechanical, and magnetic properties.

7 May 2022 in Polymer Composites
Verified
Journal Article
Closed access
AHAhmed Hassen
Ahmed Hassen
RDRalph B. Dinwiddie
Ralph B. Dinwiddie
SKSeokpum Kim
Seokpum Kim
HTHalil Levent Tekinalp
Halil Levent Tekinalp
VKVipin Kumar
Vipin Kumar
VKVlastimil Kunc
Vlastimil Kunc

Verified
Journal Article
Open access
PDF file
TFThomas Feldhausen
Thomas Feldhausen
MPMithulan Paramanathan
Mithulan Paramanathan
JHJesse Heineman
Jesse Heineman
AHAhmed Hassen
Ahmed Hassen
LHLauren Heinrich
Lauren Heinrich
BPBrian Post
Brian Post
Computer-aided manufacturing (CAM) techniques for hybrid manufacturing have led to new application areas in the manufacturing industry. In the tooling industry, cooling channels are used to enable specific heating and cooling cycles to improve the performance of the process. These internal cooling channels have been designed with limited manufacturing processes in mind, so, until recently, they were often straight in shape for cross-drilling operations and manufactured from a cast billet. To show a novel application of this common technology, a tool with integrated conformal cooling channels was manufactured using hybrid manufacturing (blown-powder DED and CNC machining) techniques. The computer-aided manufacturing strategy used, and the lessons learned are presented and discussed to enable future work in this industrial application space.

29 July 2025 in Composites Part B: Engineering
Verified
Journal Article
Closed access
KCKomal Chawla
Komal Chawla
STSegun Talabi
Segun Talabi
BRBrittany Rodriguez
Brittany Rodriguez
VKVipin Kumar
Vipin Kumar
SKSeokpum Kim
Seokpum Kim
AHAhmed Hassen
Ahmed Hassen