The design, development and analysis of a planar microstrip sensor operating at 2.4 GHz for the detection of adulteration in liquid samples is presented. The sensor characterises the samples based on the material properties which in turn affects the electric field fringing from the sensing area. In particular, a closed loop microstrip antenna is developed and used for the sensing application. The sensor is designed and analysed using simulation software and the fabricated prototype is experimentally validated. Parametric analysis of the design variables and mathematical modelling of the sensor operations are carried out by analysing the fields generated within the sensor. A case study for adulteration testing is carried out by choosing milk as the sample. Qualitative and quantitative testing using the milk as sample has been carried out experimentally under different test conditions. For quantitative testing, water is added to milk as the adulterant and for qualitative testing, usual chemical adulterants that are mixed with milk are added and the variations in operating frequency and return loss are analysed. From the analysis it could be observed that the shift in the operating frequency and return loss are dependent on the changes in dielectric permittivity of the sample loaded on to the sensor surface. From this analysis, the adulteration rate in milk can be estimated based on the variation in permittivity of the adulterant that is added to the milk. The same procedure can be extended in detecting the adulteration of any liquid samples.
In this work, a compact dielectric sensor for the detection of adulteration in solid and liquid samples using planar resonators is presented. Six types of filter prototypes operating at 2.4 GHz are presented, optimized, numerically assessed, fabricated and experimentally validated. The obtained experimental results provided an error less than 6% with respect to the simulated results. Moreover, a size reduction of about 69% was achieved for the band stop filter and a 75% reduction for band pass filter compared to standard sensors realized using open/short circuited stub microstrip lines. From the designed filters, the miniaturised filter with Q of 95 at 2.4 GHz and size of 35 mm × 35 mm is formulated as a sensor and is validated theoretically and experimentally. The designed sensor shows better sensitivity, and it depends upon the dielectric property of the sample to be tested. Simulation and experimental validation of the designed sensor is carried out by loading different samples onto the sensor. The adulteration detection of various food samples using the designed sensor is experimentally validated and shows excellent sensing on adding adulterants to the original sample. The sensitivity of the sensor is analyzed by studying the variations in resonant frequency, scattering parameters, phase and Q factor with variation in the dielectric property of the sample loaded onto the sensor.
Offshore fishing is a common occupation providing the livelihood for tens of millions worldwide. Since each fishing trip takes 5-7 days, it could be a depressing and sometimes dangerous activity especially since the fishermen have no easy way to communicate with the mainland. Currently, there is no economically viable way to stay connected. We have developed a cost-effective system for marine internet connectivity that provides assured 40+ km range which can be further extended opportunistically. This paper describes the field trials conducted to practically realize the system and presents the encouraging results obtained.
In the fast-moving world of information and communications technologies, one significant issue in metropolitan cities is water scarcity and the need for an intelligent water distribution system for sustainable water management. An IoT-based monitoring system can improve water distribution system management and mitigate challenges in the distribution network networks such as leakage, breakage, theft, overflow, dry running of pumps and so on. However, the increase in the number of communication and sensing devices within smart cities has evoked challenges to existing communication networks due to the increase in delay and energy consumption within the network. The work presents different strategies for efficient delay and energy offloading in IoT-integrated water distribution systems in smart cities. Different IoT-enabled communication network topology diagrams are proposed, considering the different water network design parameters, land cover patterns and wireless channels for communication. From these topologies and by considering all the relevant communication parameters, the optimum communication network architecture to continuously monitor a water distribution network in a metropolitan city in India is identified. As a case study, an IoT design and analysis model is studied for a secondary metropolitan city in India. The selected study area is in Kochi, India. Based on the site-specific model and land use and land cover pattern, delay and energy modeling of the IoT-based water distribution system is discussed. Algorithms for node categorisation and edge-to-fog allocation are discussed, and numerical analyses of delay and energy models are included. An approximation of the delay and energy of the network is calculated using these models. On the basis of these study results, and state transition diagrams, the optimum placement of fog nodes linked with edge nodes and a cloud server could be carried out. Also, by considering different scenarios, up to a 40% improvement in energy efficiency can be achieved by incorporating a greater number of states in the state transition diagram. These strategies could be utilized in implementing delay and energy-efficient IoT-enabled communication networks for site-specific applications.
A high Q planar chipless RFID tag with high sensitivity is proposed for communication applications. In particular, the tag structure is composed of a complementary spiral structure (CSS) that is able to provide high sensitivity and compactness. A semi analytical formula for the design of a single bit tag is derived, and the behaviour of the CSS is analysed for different dielectric substrates. Different tags, composed of up to a set of eight resonators, have been numerically and experimentally assessed. In particular, a system prototype composed of a reader and a set of tags are fabricated and experimentally assessed as a proof of concept. The system provided an operative range of tens of centimetres (a maximum operative range of 65 cm). The obtained results are quite promising and the agreement between simulated and measured results are found to be good.
29 November 2024 in Journal of Hazardous Materials Advances