Autonomous vehicles (AVs) hold the potential to revolutionize transportation by improving safety, operational efficiency, and environmental impact. However, ensuring reliability and safety in real-world conditions remains a major challenge. Based on an in-depth examination of 33 peer-reviewed studies (2015–2025), this systematic review organizes advancements across five key domains: fault detection and diagnosis (FDD), collision avoidance and decision making, system reliability and resilience, validation and verification (V&V), and safety evaluation. It integrates both hardware- and software-level perspectives, with a focus on emerging techniques such as Bayesian behavior prediction, uncertainty-aware control, and set-based fault detection to enhance operational robustness. Despite these advances, this review identifies persistent challenges, including limited cross-layer fault modeling, lack of formal verification for learning-based components, and the scarcity of scenario-driven validation datasets. To address these gaps, this paper proposes future directions such as verifiable machine learning, unified fault propagation models, digital twin-based reliability frameworks, and cyber-physical threat modeling. This review offers a comprehensive reference for developing certifiable, context-aware, and fail-operational autonomous driving systems, contributing to the broader goal of ensuring safe and trustworthy AV deployment.

The demand for electricity is continuously growing around the world and thus the need for renewable and long-lasting sources of energy has become an essential challenge. Wind turbines are considered one of the major sources of renewable electricity generation. Therefore, there is a crucial demand for wind turbine model and control systems that are capable of precisely simulating the actual wind power systems. In this paper, an advanced fuzzy logic controller is proposed to control the speed of a wind turbine system. Initially, aero dynamical, mechanical and electrical models of two mass wind turbines models are derived. Analytical calculation of the power coefficient is adopted through a nonlinear function of six coefficients that mainly depends on pitch angle and tip speed ratio. The ultimate power output from the turbine can reach up to 50 % which is achieved at zero pitch angle with an approximately tip speed ratio of eight. This is then followed by designing a hybrid fuzzy-plus I pitch controller to regulate the speed of the wind turbine shaft. In general, fuzzy logic control strategy have the advantages over traditional control techniques especially when the system is highly non-linear and has to deal with strong disturbances such as wind turbulence. To evaluate the reliability and robustness of the controller, the response of the wind turbine system is tested under several types of disturbances including wind fluctuation, sudden disturbances on high and low speed shafts. Simulation findings reveals that the performance of fuzzy-integral control technique outweighs that of conventional fuzzy approach in terms of multiple performance evaluation indexes such as zero overshoot and steady state error, rise time and a settling time of (32.9 s) (44.7 s) respectively. The reliability and robustness of the controller is tested by applying speed and torque disturbances of 25% of their maximum ranges. Results have revealed that the controller was able to reject all disturbances efficiently with a change in pitch angle up to a maximum of 10 degrees in order to retain a constant rotor speed at 1000 rpm.

Currently, one of the most important challenges facing autonomous vehicles’ development due to varying driving conditions is effective path tracking while considering lateral stability. To address this issue, this study proposes the optimization of the linear quadratic regulator (LQR) control system by using the genetic algorithm (GA) to support the vehicle in following the predefined path accurately, minimizing the sideslip, and stabilizing the vehicle’s yaw rate. The dynamic system model of the vehicle is represented based on yaw rate angle, lateral speed, and vehicle sideslip angle as the variables of the state space model, with the steering angle as an input parameter. Using the GA to optimize the LQR control by tuning the weighting of the Q and R matrices led to enhancing the system response and minimizing deviation errors via a proposed cost function of GA. The simulation results were obtained using MATLAB/Simulink 2024a, with a representation of a predefined path as a Gaussian path. Under external and internal disturbances, such as road conditions, lateral wind, and actuator delay, the model demonstrates improved tracking performance and reduced sideslip angle and lateral acceleration by adjusting the longitudinal vehicle speed. This work highlights the effectiveness of robust control in addressing path planning, driving stability, and safety in autonomous vehicle systems.

One of the most significant and widely used features currently in autonomous vehicles is the cruise control system that not only deals with constant vehicle velocities but also aims to optimize the safety and comfortability of drivers and passengers. The accuracy and precision of system responses are responsible for cruise control system efficiency via control techniques and algorithms. This study presents the dynamic cruise control system model, then investigates a genetic algorithm of the proportional–integral–derivative (PID) controller with the linear quadratic regulator (LQR) based on four fitness functions, the mean squared error (MSE), the integral squared error (ISE), the integral time squared error (ITSE) and the integral time absolute error (ITAE). Then, the response of the two controllers, PID and LQR, with the genetic algorithm was compared to the response performance of the fuzzy and fuzzy integral (Fuzzy-I) controllers. The MATLAB 2024a program simulation was employed to represent the system time response of each proposed controller. The output simulation of these controllers shows that the type of system stability response was related to the type of controller implemented. The results show that the Fuzzy-I controller outperforms the other proposed controllers according to the least Jmin function, which represents the minimum summation of the overshoot, settling time, and steady-state error of the cruise control system. This study demonstrates the effectiveness of driving accuracy, safety, and comfortability during acceleration and deceleration due to the smoothness and stability of the Fuzzy-I controller with a settling time of 5.232 s and when converging the steady-state error to zero.

The fuzzy logic controller (FLC) is considered one of the most familiar control techniques for dealing with uncertain and nonlinear systems. However, the steady-state error is still a challenge in some applications that need to be handled. To diminish this issue, an integral part has been incorporated with the fuzzy controller. This paper examines three kinds of FLC systems to improve the accuracy of the antenna's azimuth position. The three proposed controllers: basic fuzzy PD logic control system (FPD), fuzzy logic control system with an I controller (FPDI), and fuzzy logic control system plus an I controller (FPD+I) are implemented and compared in case of tracking desired antenna angle, disturbances and uncertainties using MATLAB simulation software. It has been observed that the FPD+I controller part proved effective in reducing steady-state error while delivering the best tracking performance response of the antenna's azimuth position and robustness to disturbances and uncertainties.

As the conventional control system is a controller that controls or regulates the dynamics of any other process. From time to time, this control system may not behave appropriately online; this is because of many factors like some variation in the dynamics of the process itself or unexpected changes in the environment, or even undefined parameters of the system model. To overcome the problem above, an adaptive controller is designed and implemented. This paper discusses the design of a controller for a ball and beam system with Genetic Model Reference Adaptive Control (GMRAC) for adaptive mechanism with the MIT rule. Parameter adjustment (selection) should be done using optimization methods in order to obtain an optimal performance, so genetic algorithm. (GA) will be used as an optimization method to obtain the optimum values for these parameters. As the controller, a Linear quadratic regulator (LQR) controller will be used as it is one of the most popular controllers, the performance of the proposed controller with the ball and beam system will be carried out with MATLAB Simulink in order to evaluate its effectiveness. The results show satisfactory performance where the position of the ball tracks the desired model reference.