Alison Jenifier Clarke

Ms. Alison Jenifier Clarke

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 December 2023 in Polymers
Verified
Journal Article
Open access
PDF file
Alison Jenifier ClarkeAlison Jenifier Clarke
Alison Jenifier Clarke
ADAndrew Dickson
Andrew Dickson
Denis DowlingDenis Dowling
Denis Dowling
This study investigates the feasibility of 3D printing continuous stainless steel fibre-reinforced polymer composites. The printing study was carried out using 316L stainless steel fibre (SSF) bundles with an approximate diameter of 0.15 mm. This bundle was composed of 90 fibres with a 14 μm diameter. This fibre bundle was first coated with polylactic acid (PLA) in order to produce a polymer-coated continuous stainless steel filament, with diameters tailored in the range from 0.5 to 0.9 mm. These filaments were then used to print composite parts using the material extrusion (MEX) technique. The SSF’s volume fraction (Vf) was controlled in the printed composite structures in the range from 4 to 30 Vf%. This was facilitated by incorporating a novel polymer pressure vent into the printer nozzle, which allowed the removal of excess polymer. This thus enabled the control of the metal fibre content within the printed composites as the print layer height was varied in the range from 0.22 to 0.48 mm. It was demonstrated that a lower layer height yielded a more homogeneous distribution of steel fibres within the PLA polymer matrix. The PLA-SSF composites were assessed to evaluate their mechanical performance, volume fraction, morphology and porosity. Composite porosities in the range of 2–21% were obtained. Mechanical testing demonstrated that the stainless steel composites exhibited a twofold increase in interlaminar shear strength (ILSS) and a fourfold increase in its tensile strength compared with the PLA-only polymer prints. When comparing the 4 and 30 Vf% composites, the latter exhibited a significant increase in both the tensile strength and modulus. The ILSS values obtained for the steel composites were up to 28.5 MPa, which is significantly higher than the approximately 13.8 MPa reported for glass fibre-reinforced PLA composites.

24 April 2025 in Composites Part B: Engineering
Verified
Journal Article
Open access
Alison Jenifier ClarkeAlison Jenifier Clarke
Alison Jenifier Clarke
HZHui Zhang
Hui Zhang
ADAndrew Dickson
Andrew Dickson
BZBudi Zhao
Budi Zhao
BJBen L. Jones
Ben L. Jones
Denis DowlingDenis Dowling
Denis Dowling

6 October 2024 in Journal of Composites Science
Verified
Journal Article
Open access
PDF file
Alison Jenifier ClarkeAlison Jenifier Clarke
Alison Jenifier Clarke
ADAndrew N. Dickson
Andrew N. Dickson
VMVladimir Milosavljević
Vladimir Milosavljević
Denis DowlingDenis Dowling
Denis Dowling
This study investigates the printability limitations of 3D-printed continuous 316L stainless steel fibre-reinforced polymer composites obtained using the Materials Extrusion (MEX) technique. The objective was to better understand the geometric printing limitations of composites fabricated using continuous steel fibres, based on a combination of bending stiffness testing and piezoresistive property studies. The 0.5 mm composite filaments used in this study were obtained by co-extruding polylactic acid (PLA), with a 316 L stainless steel fibre (SSF) bundle. The composite printability limitations were evaluated by the printing of a series of ’teardrop’ shaped geometries with angles in the range from 5° to 90° and radii between 2 and 20 mm. The morphology and dimensional measurements of the resulting PLA-SSF prints were evaluated using μCT scanning, optical microscopy, and calliper measurements. Sample sets were compared and statistically examined to evaluate the repeatability, turning ability, and geometrical print limitations, along with dimensional fluctuations between designed and as-printed structures. Comparisons of the curvature bending stiffness were made with the PLA-only polymer and with 3D-printed nylon-reinforced short and long carbon fibre composites. It was demonstrated that the stainless steel composites exhibited an increase in bending stiffness at smaller radii. The change in piezoresistance response of the PLA-SSF with load applied during the curvature bending stiffness testing demonstrated that the 3D-printed composites may have the potential for use as structural health monitoring sensors.