Alonso Chica Leal

Prof. Alonso Chica Leal

Central University
orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 July 2017 in International Journal of Modelling and Simulation
Verified
Journal Article
Closed access
AAAndrés Aristizábal
Andrés Aristizábal
CPCarlos Arturo Paez
Carlos Arturo Paez
Alonso Chica LealAlonso Chica Leal
Alonso Chica Leal
The initial context of this work is to evaluate the power production of solar panels under different conditions of solar radiation and temperature in order to have simulation tools to analyze the performance of photovoltaic systems. This work describes a mathematical procedure developed for estimating the power delivered by building integrated photovoltaic (BIPV) systems operating under non-standard conditions of irradiance and temperature. The model was implemented using the Matlab software, and it uses the electrical circuit equivalent of a solar cell of a single diode, which allows obtaining the curves I–V, P–V of a photovoltaic module for different levels of solar radiation and temperature. The results are compared with the data reported by the manufacturer, by calculating the percentages of relative error at the point of maximum power. It is also possible to calculate the characteristics of electrical power to the full BIPV system under standard conditions of 1000 W/m2 and 25 °C.

20 August 2020 in Energies
Verified
Journal Article
Open access
PDF file
Alonso Chica LealAlonso Chica Leal
Alonso Chica Leal
CRCésar Leonardo Trujillo Rodríguez
César Leonardo Trujillo Rodríguez
FSFrancisco Santamaria
Francisco Santamaria
This article presents a comparative experimental evaluation of some power calculation methods used for three-phase and single-phase systems. In order to make the comparison, methods based on three reference frames, the natural one, αβ and dq, are considered. This paper addresses the experimental comparison for single-phase systems facing sinusoidal and non-sinusoidal waveforms in both linear and non-linear loads. The results are obtained from an experimental platform consisting of a controlled voltage inverter and an acquisition system based on a TMS320F28335, where the power calculation algorithms are implemented. The experimental comparison of the different methods for active and reactive power calculation is made in terms of accuracy and processing time in digital implementation.

1 November 2016
Verified
Conference Paper
Closed access
Alonso Chica LealAlonso Chica Leal
Alonso Chica Leal
CRCesar Leonardo Trujillo Rodriguez
Cesar Leonardo Trujillo Rodriguez
FSFrancisco Santamaria
Francisco Santamaria
This paper presents the comparison of synchronization techniques for a photovoltaic system, which injects power to a single-phase electric grid. The single-phase system uses an electronic power inverter with a voltage and current control system, with a Bipolar-PWM modulation. The synchronization techniques try to achieve a power factor close to one for the signals at the output of the inverter, despite the presence of a polluted grid under different conditions as frequency jumps, phase-angle jumps, voltage sags and polluted by the third and fifth harmonic. Finally, the simulation results for the operation of synchronization techniques under the different disturbances of the grid using PSIM software are shown, the results of the comparison are presented and conclusions are drawn.


1 July 2013
Verified
Conference Paper
Closed access
SMSusan Montoya
Susan Montoya
RDRichard Dominguez
Richard Dominguez
ABAndrea Becerra
Andrea Becerra
LALuis Arias
Luis Arias
Alonso Chica LealAlonso Chica Leal
Alonso Chica Leal
OFOscar Florez
Oscar Florez
This paper describes the main problems that arise in a Motor Control Center by the unregulated consumption of electricity due to increased drilling oil wells and the need to treat the resulting water. The implemented solution is a reactive compensation system with automatic control of capacitor banks whose electrical variables such as active power, reactive power and average power factor are monitored through a SCADA system. This system is responsible for displaying electrical measurements, operational control and the states of the different teams as motor-pump and valves, the above in order to minimize costs in the payment of bills.

1 September 2012
Verified
Conference Paper
Closed access
LAL. A. Arias
L. A. Arias
Alonso Chica LealAlonso Chica Leal
Alonso Chica Leal
OFO. D. Florez
O. D. Florez
MBM. A. Becerra
M. A. Becerra
This paper illustrates a model for the automation of a tubular Biodigester, using UML specification. Some general topics for design and construction of Biodigester are showed. The UML model of Use Case, Class and sequence is done with the software tool astah*community 6.5.1. Writing the procedure for construction of tubular Biodigester, considering the specific characteristics of organic matter, their dimensioning and production estimates. Then, show measurements results of technical parameters in the Biodigester as the retention time, pressure, biogas volume and temperature of the surroundings, in the simple environment and in the other controlled. In the automated system performs the control of temperature and process of homogenization of the mixture within the Biodigester.