As a possible implementation of a low-power wide-area network (LPWAN), Long Range (LoRa) technology is considered to be the future wireless communication standard for the Internet of Things (IoT) as it offers competitive features, such as a long communication range, low cost, and reduced power consumption, which make it an optimum alternative to the current wireless sensor networks and conventional cellular technologies. However, the limited bandwidth available for physical layer modulation in LoRa makes it unsuitable for high bit rate data transfer from devices like image sensors. In this paper, we propose a new method for mangrove forest monitoring in Malaysia, wherein we transfer image sensor data over the LoRa physical layer (PHY) in a node-to-node network model. In implementing this method, we produce a novel scheme for overcoming the bandwidth limitation of LoRa. With this scheme the images, which requires high data rate to transfer, collected by the sensor are encrypted as hexadecimal data and then split into packets for transfer via the LoRa physical layer (PHY). To assess the quality of images transferred using this scheme, we measured the packet loss rate, peak signal-to-noise ratio (PSNR), and structural similarity (SSIM) index of each image. These measurements verify the proposed scheme for image transmission, and support the industrial and academic trend which promotes LoRa as the future solution for IoT infrastructure.

Ultra-wideband (UWB) technology can offer broad capacity, short-range communications at a relatively low level of energy usage, which is very desirable for wireless body area networks (WBANs). The involvement of the human body in such a device poses immense difficulties for both the architecture of the wearable antenna and the broadcast model. Initially, the bonding between the wearable antenna and the human body should also be acknowledged in the early stages of the design, so that both the potentially degrading output of the antenna as a consequence of the body and the possibility of exposure for the body may be handled. Next, the transmission path in WBAN is affected by the constant activity of the human body, leading to the time-varying dispersion of electromagnetic waves. Few researchers were interested in this field, and some substantial progress has recently been considered. On the other hand, this paper covered both wearable and Non-wearable UWB antenna designs and applications with respect to their substrate characteristics. Finally, this review prospectively exposes the upgraded developments of (ON-OFF) body antennas in the area of wearable and Non-wearable UWB and their implementations in the WBAN device and aims to evaluate the latest design features that inspire the performance of the antennas.

This paper presents the design and development of a planar Aligned-Gap and Centered-Gap Rectangular Multiple Split Ring Resonator (SRR) for microwave sensors that operates at a resonance frequency around 5 GHz. The sensor consists of a microstrip transmission line loaded with two elements of rectangular SRR on both sides. The proposed metamaterial sensors were designed and fabricated on Rogers RT5880 substrate having dielectric constant of 2.2 and thickness of 0.787 mm. The final dimension of the proposed sensor was measured at 35 × 14 mm². Measured results show good agreement with simulated ones as well as exhibiting high Q-factor for use in sensing application. A remarkably shift of resonance frequency is observed upon introduction of several sample with different dielectric value.

Fixed Satellite Services (FSS) used to be alone at the C-Band spectrum in most countries. Since the deployment of 5G in many countries (i.e., 3.3–3.6 GHz), FSS is not the exclusive system in the C-Band anymore. In order to minimize the detrimental interference for the FSS to allowable levels, regional exclusion zones of maximum radiated power in 5G base stations (BS) are proposed and evaluated. In this paper, a measurement campaign has been carried out, and an analysis of the interference has been studied. A filtering model, namely Filter to Remove Broadband Interference 5G (FIREBRING), is proposed and analyzed concerning the carrier-to-noise ratio (C/N). Moreover, this paper focuses on the evaluation of the 5G interference into the FSS. The proposed solution deployed an Low-Noise Block (LNB) with a band frequency of 3.7 to 4.2 GHz to test the satellite down-conversion signal at the receiver. The paper offered a complete analysis of the 5G signal, taking into account the implications of out-of-band emissions, potentially LNB saturation into FSS receiver, and the repercussions of the deployment of the 5G BS active antenna systems. With the LNB and down-converter in place, it can be found that the signal interference between 1.450 GHz and 1.550 GHz, is nearly 18 dB.

Planning of energy-efficient protocols is critical for Wireless Sensor Networks (WSNs) because of the constraints on the sensor nodes’ energy. The routing protocol should be able to provide uniform power dissipation during transmission to the sink node. In this paper, we present a self-optimization scheme for WSNs which is able to utilize and optimize the sensor nodes’ resources, especially the batteries, to achieve balanced energy consumption across all sensor nodes. This method is based on the Ant Colony Optimization (ACO) metaheuristic which is adopted to enhance the paths with the best quality function. The assessment of this function depends on multi-criteria metrics such as the minimum residual battery power, hop count and average energy of both route and network. This method also distributes the traffic load of sensor nodes throughout the WSN leading to reduced energy usage, extended network life time and reduced packet loss. Simulation results show that our scheme performs much better than the Energy Efficient Ant-Based Routing (EEABR) in terms of energy consumption, balancing and efficiency.

A flexible and totally wearable textile antenna is proposed by embroidering the conductive threads into garments. A purely polyester substrate has been utilized, which provides a tag that can be easily integrated with the clothes. The proposed tag antenna is small with dimensions of 72 × 20 × 2.75 mm³ and offers an enhanced performance in terms of gain and stability when worn on different body locations. Experimental results demonstrate an improved impedance matching owing to the elasticity of the E-shaped inductive feeder. Close agreement has been achieved between the simulated and measured results.