Anas AbuAlia

Dr. Anas AbuAlia

Civil and Environmental Engineering Department, Louisiana State University, Baton Rouge, Louisiana, USA
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 September 2024 in Innovative Infrastructure Solutions
Verified
Journal Article
Closed access
PDF file
MAMohammad Ahmad Alsheyab
Mohammad Ahmad Alsheyab
MKMohammad Ali Khasawneh
Mohammad Ali Khasawneh
Anas AbuAliaAnas AbuAlia
Anas AbuAlia
ASAnsam Sawalha
Ansam Sawalha

27 January 2021 in International Journal of Pavement Engineering
Verified
Journal Article
Closed access
MKMohammad Ali Khasawneh
Mohammad Ali Khasawneh
DADania Mohammad Al-Oqaily
Dania Mohammad Al-Oqaily
Anas AbuAliaAnas AbuAlia
Anas AbuAlia
AAAslam Ali Al-Omari
Aslam Ali Al-Omari
Bonding strength between asphalt and aggregate is considered an important feature that governs the future performance of flexible pavements. This study investigated five factors that have the potential to affect this bonding strength. Two asphalt penetration grades (60/70 and 85/100) in addition to various types of substrates (limestone, granite, marble and basalt) were used to prepare specimens to be tested by the Binder Bond Strength (BBS) test. Three aging levels (unaged, short-term aged and long-term aged) with four types of modifiers (Crumb Tire Rubber, Nano Silica, Nano Clay and Microcrystalline Synthetic Wax) were implemented for two specimen conditioning methods (dry and wet). Statistical analysis was performed to measure the influence of these factors on the asphalt-aggregate bonding strength. The results showed that aggregate type and modifier type had the most effect on the bonding strength with relatively no effect of binder type. Moreover, long term aging and two types of modifiers (Nano Silica and Crumb Tire Rubber) were found to significantly increase the Pull-Off Tensile Strength (POTS), which is a measure of the asphalt-aggregate bonding strength. Failure type was mainly cohesive in the dry condition then transformed to adhesive when specimens are exposed to moisture.

25 June 2024 in Sustainability
Verified
Journal Article
Open access
PDF file
Anas AbuAliaAnas AbuAlia
Anas AbuAlia
MAMoses Akentuna
Moses Akentuna
LMLouay N Mohammad
Louay N Mohammad
SCSamuel B. Cooper
Samuel B. Cooper
SCSamuel B. Cooper
Samuel B. Cooper
When exposed to sun radiation and heat, asphalt binders age, resulting in reduced flexibility, cracking, and pavement failure. Given the increasing demands of traffic, environmental concerns, and resource scarcity, highway agencies and researchers are actively seeking solutions that meet performance requirements and demonstrate awareness of using non-renewable resources. Epoxy asphalt (EA) promotes sustainability concepts due to its production at significantly lower mixing and compaction temperatures, enhanced durability, improved serviceability, reduced maintenance needs, and successful recycling and reuse in hot asphalt mixtures. Crumb rubber, a widely recognized recycled waste tire material, is considered a viable option for promoting sustainability and enhancing asphalt binder properties. This study aims to enhance the durability and long-term performance of asphalt binders by utilizing sustainable materials. Six types of asphalt binders were employed: PG 67-22 base asphalt binder; styrene–butadiene–styrene (SBS)-modified PG 76-22 and PG 88-22H (3.5% and 7.0% dosage rates, respectively); a hybrid PG 76-22CS-modified asphalt binder prepared with SBS and crumb rubber modifiers; and 25EAB and 50EAB epoxy-modified asphalt binders prepared at 25 and 50% dosage rates, respectively. Results indicate that the sustainable asphalt binders PG 76-22CS, 25EAB, and 50EAB demonstrated comparable or superior performance compared to SBS-modified asphalt binders, as measured by rutting and fatigue factors. Additionally, epoxy asphalt binders had better anti-aging and cracking resistance, as shown by the outcomes of Fourier-transform infrared spectroscopy and linear amplitude sweep tests, respectively. This study contributes valuable insights into the potential of sustainable materials to enhance the overall performance and resilience of asphalt binders.

30 July 2024 in Transportation Research Record: Journal of the Transportation Research Board
Verified
Journal Article
Closed access
Anas AbuAliaAnas AbuAlia
Anas AbuAlia
JLJun Liu
Jun Liu
LMLouay N Mohammad
Louay N Mohammad
SCSamuel B. Cooper
Samuel B. Cooper
SCSamuel B. Cooper
Samuel B. Cooper
Open-graded friction course (OGFC) is a thin asphalt mixture surface layer. It is gap-graded with a high percentage of coarse aggregates that are nearly uniform in size, resulting in a high percentage of interconnected air voids and asphalt binder, which provides improved skid resistance, visibility, and decreased pavement–tire noise. However, construction personnel at the Louisiana Department of Transportation and Development reported that conventional OGFC mixtures have durability issues and shorter service life, compared with thin asphalt mixture lifts. Hence, effects of different asphalt binder types on the performance of OGFC mixtures were evaluated. Five types of asphalt binder were utilized: conventional styrene-butadiene-styrene (SBS) asphalt binder PG 76-22M; high SBS content asphalt binder PG 88-28; diluted epoxy asphalt (EA) binder with two different dosages (25% and 50%); and a hybrid modified asphalt binder prepared with SBS and crumb rubber modifier PG 76-22G. The optimal aggregate structures were determined based on minimum required air voids and voids in coarse aggregate. Physical and mechanical tests were conducted to assess the performance of OGFC mixtures, including draindown, permeability, loaded wheel track, and Cantabro abrasion loss. Results indicate that OGFC mixtures incorporating diluted EA binder exhibited lower draindown values than mixtures containing PG 76-22M and PG 88-28. Moreover, mixtures with PG 88-28 and 50% EA binders demonstrated improved resistance to rutting. Mixtures with 50% EA and PG 88-28 binders demonstrated improved durability, compared with mixtures with PG 76-22M for unaged and aged conditioning, as measured by Cantabro abrasion loss values.

12 June 2025 in Transportation Research Record: Journal of the Transportation Research Board
Verified
Journal Article
Closed access
Anas AbuAliaAnas AbuAlia
Anas AbuAlia
LMLouay N Mohammad
Louay N Mohammad
Ahmed HemidaAhmed Hemida
Ahmed Hemida
SCSamuel B. Cooper
Samuel B. Cooper
Open-graded friction course (OGFC) is a thin asphalt mixture surface layer designed primarily to improve the functionality of a roadway. It is designed with a special aggregate structure with high air voids and stone-on-stone contact that accelerates rainwater drainage. It has many advantages, such as reducing hydroplaning, splashing, and spray, and enhancing roadway visibility and skid resistance under wet weather conditions. However, these mixtures exhibit premature failures and moisture damage that limit their usage in pavement construction. Further, the current specifications might inaccurately reflect field conditions. Therefore, this study was aimed at evaluating and comparing the effect of various asphalt binder types on the performance of OGFC mixtures under different aging and moisture conditions. Three types of asphalt binder were utilized: conventional styrene-butadiene-styrene asphalt binder performance grading (PG) 76-22M and diluted epoxy asphalt (EA) binder with two different dosages. A suite of physical and mechanical tests was conducted to evaluate OGFC mixtures, namely, draindown, permeability, Hamburg wheel tracking (HWT) test for rutting and moisture susceptibility, Cantabro abrasion loss test for durability, semi-circular beam (SCB) for fracture resistance, and indirect tensile strength (ITS) test for tensile strength and moisture susceptibility. Results indicated that EA mixtures exhibited improved draindown results, compared with 76M mixture. Further, the developed cross-linked network associated with EA binder might explain the improved rutting and abrasion loss resistance. EA mixtures showed significantly better moisture resistance, as measured by HWT, ITS, and SCB tests. Cost-effectiveness ratio results showed higher effectiveness for EA mixtures than conventional 76M mixture.

28 August 2025 in Construction and Building Materials
Verified
Journal Article
Closed access
Anas AbuAliaAnas AbuAlia
Anas AbuAlia
IBRAHIM ELNAMLIBRAHIM ELNAML
IBRAHIM ELNAML
LMLouay N Mohammad
Louay N Mohammad
SCSamuel B. Cooper
Samuel B. Cooper