Anita Ptak

Dr. Anita Ptak

Wrocław University of Science and Technology, Wrocław, Dolnośląskie, Poland
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
APAnita Ptak
Anita Ptak
PTPaula Taciak
Paula Taciak
Wojciech WielebaWojciech Wieleba
Wojciech Wieleba
This article concerns the tribological properties of three selected polymer materials: polyamide PA6, polyethylene PE-HD and polyetheretherketone composite PEEK/BG during sliding against aluminium alloy EN AW-2017A in the presence of hydraulic oil HLP 68. The tests were carried out under contact pressure p of 3.5–11 MPa at ambient temperature T ranging from −20 °C to +20 °C. The dependence of kinetic friction coefficient μk on the two parameters was determined through tribological tests carried out using a pin-on-disc tribometer. A five-level central composite rotatable design (CCRD) was adopted for the experiment. All the test results were statistically analysed. The microhardness of the surface of the polymeric material was measured before and after the friction process. The surface was also examined under SEM. Temperature and contact pressure have been found to have a significant effect on the tribological properties of the tested sliding pairs. Relative to the applied friction conditions, the surfaces after friction showed rather heavy signs of wear.

23 December 2024 in Coatings
Verified
Journal Article
Open access
PDF file
JSJustyna Sokolska
Justyna Sokolska
APAnita Ptak
Anita Ptak
Polyurethane coatings are widely used as protective layers against wear, mainly abrasive wear. They have recently been applied to surfaces exposed to erosive wear, such as wind turbine blades. This study investigated the abrasive and erosive wear of polyurethane elastomeric coatings with hardness values of 55 ShA, 75 ShA, and 95 ShA. The abrasive wear test was carried out using loose abrasive grains. The erosive wear test was carried out using a pressurized stream of gas containing abrasive particles. Both tests were carried out using aluminum oxide grains of five different sizes to evaluate the effect of particle size on wear behavior. Microscopic and profilometric analyses of the surface of the wear tracks were carried out. The mechanism of abrasive and erosive wear of polyurethane elastomeric coatings was determined. The results of the tests show a non-linear dependence of abrasive and erosive wear on the grain size. Furthermore, polyurethane elastomer coatings with a higher hardness exhibit a lower abrasive wear resistance but higher susceptibility to erosive wear. These findings provide insight into the trade-offs between hardness and wear performance, offering practical guidance for selecting polyurethane coatings in applications requiring resistance to combined abrasive and erosive wear.

1 April 2025 in Materials
Verified
Journal Article
Open access
PDF file
Maciej KujawaMaciej Kujawa
Maciej Kujawa
APAnita Ptak
Anita Ptak
3D printing is becoming widely used and printed parts very often replace extruded parts. Plastics, due to their ability to work with steel without lubrication, are commonly used for sliding components and are therefore exposed to various types of wear, including abrasive wear. In this paper, abrasive wear resistance tests were carried out to compare extruded and 3D-printed samples. Moreover, microhardness tests, surface topography and microscopic observations of the surface of the samples before and after friction were also conducted. Samples were made from eight materials that are most commonly used in 3D FDM printing: PLA, PET-G, ABS, PA, PP, PC, PMMA and HIPS. For six out of the eight materials tested, samples made by extrusion proved to be more resistant to abrasive wear (between 10% and 24%) than those printed ones. Fabrication by 3D printing can lead to different object properties and thus different abrasion resistance. The abrasion resistance of extruded samples depends on factors reported in the literature such as hardness, density and surface roughness. In the case of 3D printed samples, no such relationship was found. For this reason, the researchers believe that the reduced abrasion wear resistance of printed samples is due to their specific internal structure.

1 September 2015 in Colloids and Surfaces A: Physicochemical and Engineering Aspects
Verified
Journal Article
Closed access
ADAnna Dobrowolska
Anna Dobrowolska
Piotr KowalewskiPiotr Kowalewski
Piotr Kowalewski
APAnita Ptak
Anita Ptak

29 February 2016 in Tribologia
Verified
Journal Article
Closed access
APAnita Ptak
Anita Ptak
The surface layer of the polymeric sliding materials co-operating with steel has an impact on the tribological properties at low temperatures. The goal of the present study was to determine the impact of the friction process parameters on the change in the surface layer of the polymeric materials. Three polymeric materials, namely PA6, PEEK, and PTFE, were tested. The materials were used for the sliding pairs with the typical construction steel C-45. At first, the tribological investigation at a low temperature T = (–50–0)°C was performed. Before and after that, the friction surface of the polymers, including the surface roughness and microhardness, were evaluated. During the experiment, variable parameters were the sliding velocity (v = 0.5 – 2 [m/s]) and the unit pressure (p = 0.5 – 3 [MPa]). The research has shown changes in the surface layer after the tribological tests at low temperatures. Strengthening and smoothing of the friction surface were observed, depending on the assumed process parameters.

1 July 2018 in Tribologia
Verified
Journal Article
Closed access
APAnita Ptak
Anita Ptak
Piotr KowalewskiPiotr Kowalewski
Piotr Kowalewski
For the polymeric materials, changing of the temperature causes changes in mechanical and tribological properties of sliding pairs. The goal of the present study was to determine the change in Young's modulus and kinetic friction coefficient depending of the temperature. Three thermoplastic polymers, PA6, PET and PEEK, were tested. These materials cooperated in sliding motion with a C45 construction steel disc. As part of the experiment, the Young's modulus tests (by 3-point bending method) and kinetic friction coefficient studies (using pin-on-disc stand) were carried out. The temperature range of mechanical and tribological tests was determined at T = –50°C±20°C. Comparing the results of mechanical and tribological properties, there is a tendency to decrease the coefficient of friction as the Young's modulus increases while reducing the working temperature.