Anthony C. Ogazi

Dr. Anthony C. Ogazi

Chemical Engineering, Vaal University of Technology, Vanderbijlpark, Gauteng, South Africa
orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 May 2023 in Journal of Polymers and the Environment
Verified
Journal Article
Open access
PDF file
Anthony C. OgaziAnthony C. Ogazi
Anthony C. Ogazi
Peter Ogbemudia OsifoPeter Ogbemudia Osifo
Peter Ogbemudia Osifo
The effect of 3D printed modified Chitosan membranes on bacterial strains by water filtration system was explored in this study. Specifically, it focused on the characterisation of 3D printed Chitosan–graphene oxide–silver nanoparticles (CS–GO–AgNP) composite membranes and the effects of Dimethylacetamide (DMAc) used as co-solvent on the performance of the CS–GO–AgNP nanocomposites. It also examined the impact of GO–AgNP on the CS matrix for inhibition of Fecal Coliforms, Total Coliforms and Escherichia coli (E. coli) bacterial strains in contaminated surface water. The increase in DMAc concentration and subsequent reduction in CS mole fraction within the ink formulation resulted to wider distribution of AgNP across membrane surface, improvement in mechanical strength and surface hydrophilicity of the modified CS membranes. Similarly, increase in GO–AgNP concentration effectively reduced the spread of the identified microorganisms. Sample B-12 with 79% CS, 21% DMAc and 1.2 ml of GO–AgNP exhibited the highest inhibition of the bacterial strains, with more than 95% of Fecal and Total Coliforms suppressed or inactivated, while 99.9% of the E. coli bacterial cells were completely prevented, indicating that our 3D printed modified CS membranes can effectively be used for water treatment.

4 January 2023 in Polymers for Advanced Technologies
Verified
Journal Article
Closed access
Anthony C. OgaziAnthony C. Ogazi
Anthony C. Ogazi
Peter Ogbemudia OsifoPeter Ogbemudia Osifo
Peter Ogbemudia Osifo

24 July 2023 in Journal of Applied Polymer Science
Verified
Journal Article
Open access
Anthony C. OgaziAnthony C. Ogazi
Anthony C. Ogazi
Peter Ogbemudia OsifoPeter Ogbemudia Osifo
Peter Ogbemudia Osifo
This study investigated the dynamics of drop formation and the printability of chitosan/silver nanoparticles composite fluid (CS/AgNP) modified with polyvinyl alcohol (PVA) using an inkjet 3D printer. It specifically investigated the relationship between rheological properties and fluid mechanical properties in determining the minimum drop velocity for 3D printing of modified CS ink. Proper matching of modified CS fluid rheological properties to the established physical parameters generated adequate droplets on glass substrates and formed membrane composites. The dynamic viscosity of the CS ink decreased with an increase in the concentration of PVA, which resulted in the disruption of existing molecular forces within the CS/AgNP polymer chains, suggesting that the solvent (PVA) was responsible for reducing the shear stress, surface tension, and viscosity of the composite membranes and subsequently improving the flow rates of the CS matrix at the nozzle orifice. Optimized drop velocity of 1.77 m/s yielded adequate formation of the CS/AgNP/PVA membrane composite with enhanced surface morphology, while an increase in drop velocity to 2.5 m/s brought about the formation of satellite droplets with irregular surface structures in printed CS composites. Therefore, adherence to minimum fluid drop velocity is fundamental to effective inkjet printing of composite membranes.

5 October 2023 in Applied Surface Science Advances
Verified
Journal Article
Open access
Anthony C. OgaziAnthony C. Ogazi
Anthony C. Ogazi
POPeter O. Osifo
Peter O. Osifo

18 December 2025 in Polymers for Advanced Technologies
Verified
Journal Article
Open access
Anthony C. OgaziAnthony C. Ogazi
Anthony C. Ogazi
IOIyiola O. Otunniyi
Iyiola O. Otunniyi
DMDavid A. Mauchline
David A. Mauchline
The properties and functionalities of polyamide (PA) 12 printed products depend greatly on the appropriate selection of process routes, the compatibility‐cost relationship, and the fundamental properties of the polymer powder. This study reviews the existing PA12 powder preparation methods, challenges, and future prospects. High capital and operational costs, stringent safety protocols, potential material degradation, and environmental issues are some of the major challenges associated with PA12 production. However, the dissolution‐precipitation process seemed more viable than other techniques because of its ability to produce PA12 polymer powder with a narrow pore size distribution, improved mechanical strength, and enhanced production efficiency. Variables such as solvent type, concentration, dissolution temperature, and pressure effectively regulate the solubility and phase separation of the polymer powder. The thermally induced phase separation (TIPS) process enables easy incorporation and uniform distribution of reinforcements within a soluble polymer matrix. The utilization of green solvents for the dissolution of PA12 would provide viable alternatives to hazardous chemicals and mitigate environmental pollution, while an appropriate solvent recovery process would minimize production cost and improve powder productivity.

17 April 2025 in Polymer Engineering & Science
Verified
Journal Article
Open access
Anthony C. OgaziAnthony C. Ogazi
Anthony C. Ogazi
IOIyiola O. Otunniyi
Iyiola O. Otunniyi
DMDavid A. Mauchline
David A. Mauchline
A novel approach to investigate the processability of polyamide 12/dimethylacetamide (PA12/DMAc) microspheres for laser sintering through molecular interactions of the functional groups and the effects of DMAc on the morphology, particle size distribution, and thermal properties of the polymer composites was addressed in this study. The increase in DMAc concentrations enhanced polymer dissolution, minimized agglomeration, and improved the binding adhesive forces within the polymer matrix. It also enhanced the stretching vibrations in the primary amide (C=N), amine bond (C–N), and hydrogen bond (N–H) of the PA12. The melting enthalpy of the polymer powder increased with greater molecular interactions with the solvent. All the PA12 powder samples exhibited a consistent average crystallization point of 147.5°C, similar to that of virgin PA12 (149.3°C) due to identical exothermic properties. The SEM and particle size distribution analysis of PA12/DMAc samples indicated variability in molecular interspaces between powder particles due to differences in the interfacial mobility, which expanded with an increase in the solvent input ratios. However, the particle size distribution span reduced with an increase in the volume of DMAc. The optimal mean particle size distribution was 64.87 μm, accompanied by a bulk density of 0.38 g/cm3, which could facilitate the sinterability of the PA12 powder.Highlights: Compatibility of PA12/DMAc microspheres Molecular interactions during TIPS Effects of DMAc on PA12 dissolution and precipitation time Dissolution and precipitation rate analysis Melting and crystallization behavior.