Antonio Mancuso

Prof. Antonio Mancuso

University of Palermo (Palermo, Italy)
orcid

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2015 in Procedia Engineering
Verified
Journal Article
Open access
Antonio MancusoAntonio Mancuso
Antonio Mancuso
Giuseppe PitarresiGiuseppe Pitarresi
Giuseppe Pitarresi
DTDavide Tumino
Davide Tumino
This work investigates the flexural behavior of a composite sandwich made of flax fibers reinforced skin facings and an agglomerated cork core, to be employed as an eco-friendly solution for the making of structural components of small sailing boats. An experimental mechanical characterization of the strength and stiffness flexural behavior of the proposed sandwich is carried out, providing a comparison of performances from three implemented assembling techniques: hand-lay-up, vacuum bagging and resin infusion. Sandwich beams have been tested under three point bending (TPB) at various span lengths. A procedure is also proposed and implemented to consider the potential influence of the local elastic indentation in the experimental evaluation of the flexural stiffness. This procedure is based on the analytical solution of an indented beam resting on a fully backed Winkler foundation

1 February 2006 in Ocean Engineering
Verified
Journal Article
Closed access
Antonio MancusoAntonio Mancuso
Antonio Mancuso

3 November 2015 in Materials
Verified
Journal Article
Open access
PDF file
Giuseppe PitarresiGiuseppe Pitarresi
Giuseppe Pitarresi
DTDavide Tumino
Davide Tumino
Antonio MancusoAntonio Mancuso
Antonio Mancuso
The present work describes the experimental mechanical characterisation of a natural flax fibre reinforced epoxy polymer composite. A commercial plain woven quasi-unidirectional flax fabric with spun-twisted yarns is employed in particular, as well as unidirectional composite panels manufactured with three techniques: hand-lay-up, vacuum bagging and resin infusion. The stiffness and strength behaviours are investigated under both monotonic and low-cycle fatigue loadings. The analysed material has, in particular, shown a typical bilinear behaviour under pure traction, with a knee yield point occurring at a rather low stress value, after which the material tensile stiffness is significantly reduced. In the present work, such a mechanism is investigated by a phenomenological approach, performing periodical loading/unloading cycles, and repeating tensile tests on previously “yielded” samples to assess the evolution of stiffness behaviour. Infrared thermography is also employed to measure the temperature of specimens during monotonic and cyclic loading. In the first case, the thermal signal is monitored to correlate departures from the thermoelastic behaviour with the onset of energy loss mechanisms. In the case of cyclic loading, the thermoelastic signal and the second harmonic component are both determined in order to investigate the extent of elastic behaviour of the material.

27 February 2015 in International Journal on Interactive Design and Manufacturing (IJIDeM)
Verified
Journal Article
Closed access
PDF file
TITommaso Ingrassia
Tommaso Ingrassia
Antonio MancusoAntonio Mancuso
Antonio Mancuso
VNVincenzo Nigrelli
Vincenzo Nigrelli
DTDavide Tumino
Davide Tumino

16 October 2012 in International Journal on Interactive Design and Manufacturing (IJIDeM)
Verified
Journal Article
Closed access
PDF file
TITommaso Ingrassia
Tommaso Ingrassia
Antonio MancusoAntonio Mancuso
Antonio Mancuso

Verified
Journal Article
Open access
PDF file
TITommaso Ingrassia
Tommaso Ingrassia
Antonio MancusoAntonio Mancuso
Antonio Mancuso
VNVincenzo Nigrelli
Vincenzo Nigrelli
ASAntonio Saporito
Antonio Saporito
DTDavide Tumino
Davide Tumino
In this paper, a tool able to support the sailing yacht designer during the early stage of the design process has been developed. Cubic Rational Bézier curves have been selected to describe the main curves defining the hull of a sailing yacht. The adopted approach is based upon the definition of a set of parameters, say the length of waterline, the beam of the waterline, canoe body draft and some dimensionless coefficients according to the traditional way of the yacht designer. Some geometrical constraints imposed on the curves (e.g., continuity, endpoint angles, curvature) have been conceived aimed to avoid unreasonable shapes. These curves can be imported into any commercial Computer Aided Design (CAD) software and used as a frame to fit with a surface. The resistance of the hull can be calculated and plotted in order to have a real time estimation of the performances. The algorithm and the related Graphical User Interface (GUI) have been written in Visual Basic for Excel. To test the usability and the precision of the tool, two existing sailboats with different characteristics have been successfully replicated and a new design, taking advantages of both the hulls, has been developed. The new design shows good performances in terms of resistance values in a wide range of Froude numbers with respect to the original hulls.