Ceramizable (ceramifiable) silicone rubber-based composites are modern elastomeric materials for fire protection application. The most important sector of economy using such materials is cable industry because there are special types of electric circuits that have to keep working in the case of fire. These kinds of composites can create ceramic phase protecting copper wire from melting under high temperature. When temperature increases, polymer matrix degrades (creating silica residue as one of the products) and mineral particles dispersed in silicone rubber matrix stick together creating stiff, durable, insulating and porous ceramic skin. In this paper, the influence of surface modification of montmorillonite with quaternary ammonium salts on ceramization of their silicone rubber composites is presented. Filler modification was studied, determining changes to its surface energy and thermal stability. Mechanical properties, flammability and thermal stability of composites were determined. Ceramization of the composites was discussed from the point of view of their mechanical properties and structure of ceramic phase after heat treatment, determined by compression stress tests, porosimetry and scanning electron microscopy adequately. Results show that type of modifier applied strongly affects properties of silicone rubber-based ceramizable composites before and after ceramization. Samples containing surface-modified montmorillonite produce significantly less heat during their thermal decomposition than composite filled with unmodified montmorillonite. Moreover, incorporation of montmorillonite modified with ammonium salt of linear organic chain causes the creation of nano-porous structure after ceramization. On the one hand, it facilitates heat insulation, but on the other hand, high total volume of pores adversely affects mechanical endurance of the ceramic phase.
16 November 2015 in Journal of Thermal Analysis and Calorimetry
Ceramizable (ceramifiable) silicone composites are one of the most important elastic technical materials produced industrially. These composites are commonly used to increase flame retardancy of electrical cables and to ensure integrity of electricity network during fire by their ability to create a continuous ceramic structure. In this paper, ceramizable silicone composites filled with different contents of carbon fibers were tested. The research was focused on the characterization of ceramic structure created during heat treatment of the composites and thermal properties of the composites. For this purpose, morphology (SEM) and compression strength of the ceramic structures were studied. To describe process of ceramic structures creation, TG/DSC analysis was done. These tests have demonstrated that, the increase in carbon fibers amount improves the mechanical properties of ceramic structure regardless of heat treatment conditions.
It is widely acknowledged that waste sulfur generated from the petroleum industry creates huge storage and ecological problems. Therefore, the various methods of utilization are becoming increasingly attractive research topics worldwide. The thermal ability of elemental sulfur to homolytic cleavage of S8 rings enables its free radical copolymerization with unsaturated organic species and the obtaining of chemically stable polymeric materials. Here we report a novel possibility to use sulfur/organic copolymers obtained via “inverse vulcanization” as curatives for rubber. For this purpose, several various sulfur/organic copolymers were synthesized and analyzed from the point of view of their performance as rubber crosslinking agents. Solvent extraction was used to purify sulfur/organic copolymers from unreacted (elemental) sulfur. Thermal properties of the prepared copolymers were characterized by thermogravimetric analysis and differential scanning calorimetry (TGA–DSC). Crosslink density and structure of cured elastomers was studied by equilibrium swelling, thiol-amine analysis and freezing point depression. Mechanical properties of the vulcanizates were determined under static and dynamic conditions (DMA—dynamic mechanical analysis). It is proved that the utilization of sulfur/organic copolymers as curatives enables an effective crosslinking process of rubbers. Taking into account the results of a crosslink density analysis and mechanical properties of the vulcanizates cured with purified copolymers, it is evident that relatively long copolymer macromolecules are also involved in the formation of chemical bonds between unsaturated rubber macromolecules.
The aim of this work is to describe the changes in the properties of ceramifiable silicone rubber-based composites caused by the incorporation of novel alternative minerals in comparison to other popular, widely utilized fillers. TiO2, calcined kaolin and calcium-based minerals mix (CbMix) consisting of CaO (6.26 wt%), CaCO3 (26.18 wt%) and Ca(OH)2 (67.56 wt%) have not been considered as a dispersed phase of ceramifiable silicone composites destined for wire covers yet. Mineral fillers: TiO2 (anatase), mica (phlogopite), CbMix, CaCO3, Al(OH)3, kaolin and calcined kaolin affect the processing and the various properties of silicone rubber-based composites destined for wire covers differently. The properties—flammability, smoke intensity, micromorphology and mechanical durability after ceramification—are assessed by measuring: the kinetics of vulcanization, stress at different levels of elongation, tensile strength and the elongation at break of the materials. Although the curing process of the composites is disturbed by the addition of CbMix, it benefits from an increase in oxygen index value, which reaches 31.4%. What is more, also its flammability parameters measured by cone calorimetry improve, such as the total heat released (THR) reaching 9.3 MJ/m2. Samples containing kaolin and calcined kaolin exhibit the best mechanical properties before ceramification, whereas composites filled with calcium-based powders (CbMix, CaCO3) mechanically display the strongest mineral char after heat treatment, possibly due to a more homogenous micromorphology and the creation of calcium silicates at elevated temperature. Significant amounts of wollastonite, parawollastonite and pseudowollastonite are visible in their structure after ceramification.