Ayi Bahtiar

Dr. Ayi Bahtiar

Department of Physics, Universitas Padjadjaran
+1
orcid

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 May 2017 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
ABAyi Bahtiar
Ayi Bahtiar
SRS Rahmanita
S Rahmanita
YIY D Inayatie
Y D Inayatie

25 September 2024 in Journal of Fluorescence
Verified
Journal Article
Closed access
PDF file
SWSriati Wahyudi
Sriati Wahyudi
IRIvan Rizoputra
Ivan Rizoputra
CPCamellia Panatarani
Camellia Panatarani
FFFerry Faizal
Ferry Faizal
ABAyi Bahtiar
Ayi Bahtiar

1 January 2016 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
MZMuhammad Hilmi Zulkifli
Muhammad Hilmi Zulkifli
ABAyi Bahtiar
Ayi Bahtiar
Perovskite materials have become great research interest due to their superior properties for high power conversion efficiency (PCE) solar cells. Recently, a PCE above 18% is already achieved using perovskite methylamonium lead iodide (CH3NH3PbI3, MAPbI3) as active material. High quality crystal of perovskite film as active material is very crucial to be controlled for obtaining high PCE with high environmentally stable solar cells. Spin-coating and dip-coating methods are commonly used to prepare perovskite films for solar cells. However, not all lead(II) iodide PbI2 can be completely converted into perovskite which cause low PCE and deteriorate the stability of solar cells. Therefore, a suitable and simple method for obtaining high quality crystal MAPbI3 film is highly needed. Herein, we report our current study on the optical, structural and morphological properties of perovskite CH3NH3PbI3 films prepared by use of two-step spin coating method. By using this method, no PbI2 peak is observed in the XRD pattern of perovskite film which proves that all PbI2 was fully converted into perovskite CH3NH3PbI3.

1 January 2016 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
YYYayah Yuliah
Yayah Yuliah
ABAyi Bahtiar
Ayi Bahtiar
FIFitrilawati
Fitrilawati
RSRustam E. Siregar
Rustam E. Siregar
ZnO Nanoparticles (NPs) has unique natures on their crystal structure, direct band gap and high exciton binding energy, consequently applied in optoelectronic devices such as solar cells, optical wave guide and light emitting diodes (LED). However the drawback was ZnO NPs tend to agglomerate and turn to nano-structured materials with poor properties. Effort to avoid agglomerations generally resolved by surface modification of ZnO NPs to obtain well-dispersed suspension. However changes in the surface of ZnO NPs may change the electronic structure and density of states of ZnO NPs, in turn may change the optical band gap. Thus, the objective of current research is investigation of optical band gap of ZnO NPs due to surface modification by capping agent of poly-4-vinylpyrrolidone (PVP) molecules. Uncapped and PVP-capped ZnO nanoparticles were prepared by sol-gel method. The characteristics of surface modifications were investigated by UV-Vis and Photo Luminescence spectroscopy and Transmission Electron Microscope (TEM). The results shows the surface modification has change the band gap of ZnO NPs obtained at second precipitated stage. In contrast, the change of the optical band gap did not observe due to the surface modification of ZnO NPs obtained at the first stage. It was concluded that PVP capping on ZnO NPs did not affect on the band gap when the capping was performed on first stage. It is emphasized that this statement also supported by TEM images observations.

1 January 2016 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
IDIlham Dhiaputra
Ilham Dhiaputra
BPBayu Permana
Bayu Permana
YMYusep Maulana
Yusep Maulana
YIYuniar Dwi Inayatie
Yuniar Dwi Inayatie
YPYonatan R. Purba
Yonatan R. Purba
ABAyi Bahtiar
Ayi Bahtiar
Perovskite solar cells have been intensively investigated for high performance and low-cost solid-state solar cells. Perovskite based-lead materials are commonly used as active material for high power conversion efficiency solar cells. Herein, we report our study on the development of used electrodes car battery as a cheap raw lead material to be converted into lead (II) iodide PbI2 by using simple chemical method. We have successfully obtained PbI2 material with purity higher than 85% and its crystal structure is comparable with that of commercial product. The perovskite CH3NH3PbI3 film was prepared by spin-coating of PbI2 solution and followed by spin-coating two-times of methylamonium iodide (MAI) solution. In this paper, the crystal structure of perovskite film attained from used car battery is shown and compared with that of prepared from commercial PbI2. By utilizing the used car battery into perovskite valuable material for high performance solar cells, we can not only improve the economical value (added-value) of wasted car battery but also we can simultaneously save the environment.

19 January 2022 in Nanomaterials
Verified
Journal Article
Open access
PDF file
ABAyi Bahtiar
Ayi Bahtiar
MHMila Sri Hardiati
Mila Sri Hardiati
FFFerry Faizal
Ferry Faizal
VMVanitha Muthukannan
Vanitha Muthukannan
CPCamellia Panatarani
Camellia Panatarani
IJI Made Joni
I Made Joni
Recently, sophisticated technologies are applied to design a certain surface nature that can have superhydrophobic properties. Thus, a simple spray technique was introduced to prepare a superhydrophobic surface using rGO with Ni-S system (rGO-Ni) by using NiSO4 catalyst under microwave irradiation at various reaction times of 5, 10, 20, and 30 min. The GO reduction was conducted at a fixed Ar/H2 ratio, a flow rate of 0.4 L/min, microwave power of 720 W, and a mass of 0.5 g. GO powder with nickel sulfate catalyst was treated under Ar/H2 (4:1) mixture for GO reduction, where Ar and H2 were expected to prevent the rebinding of oxygen released from GO. The result of XRD and Raman measurement confirms that rGO-Ni prepared at reaction time 20 min exhibit the highest reduction of GO and the presence of various Ni-S crystal structures such as NiS, NiS2, Ni3S2, and Ni3S4 due to decomposition of NiSO4. The rGO-Ni coating performance shows superhydrophobic nature with a contact angle of 150.1°. The AFM images show that the addition of nickel to rGO produces a quasi-periodic spike structure, which increases the superhydrophobicity of the r-GO-Ni coated glass with a contact angle of 152.6°. It is emphasized that the proposed simple spray coating using rGO-Ni provides a more favorable option for industry application in obtaining superhydrophobic surfaces.