The addition of graphene nanosheets (GNSs) in lubricating grease could significantly reduce the interfacial friction and improve the load-bearing capacity of the parts. Therefore, it has been considered as having great potential as lubricant additives. In this study, we synthesized GNSs that are prepared by a modified Hummer method, and investigated the effect of GNS with different concentration (0.5%, 1%, 2%, 3%, and 4 wt%) on the tribological properties of the calcium grease. The friction and wear experiments were performed using a four-ball tribometer. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) were employed to examine the GNS and the friction mechanisms. Results indicate that the friction reduction ability and anti-wear property of the base grease can be improved with the addition of GNS. It was also found that the friction reduction decreases by 61%, and the wear scar diameter (WSD) decreases by 45%, and the extreme-pressure (EP) properties increased 60% at 3 wt% GNS. It is clear that the GNS in grease easily forms protective deposited films to prevent the rubbing surfaces from coming into direct contact, thereby improving the entire tribological behavior of the grease. GRAPHICAL ABSTRACT

Purpose: The purpose of this paper is to fabricate composite nanogrease for tribological applications. Multi-walled carbon nanotubes (MWCNTs) with a size 10 nm average diameter and 5 μm in length were used as additives to calcium grease. Design/methodology/approach: The tribological four-ball machine was used to evaluate calcium grease with carbon nanotubes (CNTs) as an additive. The interaction between CNT and calcium grease (nanogrease) were studied by transmission electron microscopy and X-ray diffraction. Findings: MWCNTs composite nanogrease was manufactured for tribological applications. The effectiveness of the fabricated grease in improving the tribological performance at different concentrations and under different loads was tested. The results are summarized as follows. CNT nanoparticle additive dispersed in calcium grease significantly improve its anti-wear performance, reducing friction, increasing load-carrying capacity and extreme pressure (EP) property. The friction is reduced by about 50 per cent, the wear scar diameter (WSD) decreased to 32 per cent and the EP properties increases about 38 per cent, with only 3 wt.%. The modified grease with CNTs additives of 3 wt.% showed the most favorable results. Energy dispersive x-ray (EDX) analysis shows that C was present on the worn scar surface, with atomic concentration of about 22 per cent. The presence of C suggests that a lubricating film is likely formed because of the presence of CNTs and very likely prevented the steel-to-steel direct contact. Originality/value: The results indicated that a 3 wt.% of MWCNT nanogrease is an excellent antiwear, with EP and low friction coefficient. It was also found that the friction coefficient was reduced to about 50 per cent, the WSD decreased by about 32 per cent and the EP properties increased about 38 per cent. The mating surfaces were investigated with scanning electron microscopy and EDX. The results show that a boundary film mainly composed of CNTs, Cr and Fe was formed on the rubbed surfaces.

Fracture in the hip joint is a major and quite common health issue, particularly for the elderly. The loads exploited by the lower limbs are very acute and severe; in the femur, they can be several folds higher than the whole weight of the body. Nanotechnology and nanocomposites offer great potential in biomedical applications. The organic materials are more biocompatible. Mechanical properties like strength and hardness are challenging parameters which control the selection of a joint. HDPE in its pure form has been successfully used as a prosthetic foot (external) but failed as an implant material due to limited mechanical properties. High-density polyethylene thermoplastic polymer (HDPE) and multi-walled carbon nanotubes (MWCNT)/Nano-Alumina is selected as a potential material for a biomedical implant and its mechanical properties and biocompatibility have been discussed. HDPE/MWCNT/Alumina (Al₂O₃) nanocomposites have not been explored yet for prosthetic implants. These nanocomposites were prepared in this investigation in different compositions. Prepared material has been physiochemically characterized to check the morphology and the structure. MWCNTs enhanced hardness and elastic modulus of the HDPE. Optimization of the material composition revealed that hybrid composite with structure (2.4% Al₂O₃ and 0.6% MWCNT) exhibits better mechanical properties compared to other ratios with 3% MWCNTs and 5% MWCNTs. Thermal gravimetric analysis (TGA) dedicates that the percentage of crystallization has been increased to 6% after adding MWCNT to HDPE. The moisture absorption decreased to 90% with 5% MWCNT. Experimental results of Colorimetric assay (MTT) of a normal human epithelial cell line (1- BJ1) over Al₂O₃/MWCNT@HDPE showed <20% cytotoxic activity, proving its acceptance for medical use. HDPE/MWCNT/Al₂O₃ nanocomposites emerged as a candidate material for artificial joints. Graphical abstract

Recently, nanofluids attract considerable interest for enhanced rheological behavior and thermal performance. The aim of this research is to study the influence of additives Multi-Walled Carbon Nanotubes (MWCNTs) on the rheological behavior and its structure, thermal conductivity, and the influence of shear thinning rate on oil separation at different temperatures for calcium grease. Various concentrations of MWCNTs (0.5, 1, 2, 3, and 4%) have been added to the grease to obtain the best percentages that improve the properties of nanofluid. The microstructure of MWCNTs and nanofluid were examined by X-ray diffraction (XRD), Transmission Electron Microscope (TEM), and Scanning Electron Microscope (SEM). These experimental investigations were evaluated with a Brookfield programmable Rheometer DV-III ULTRA. The results indicated that the optimum concentration of MWCNTs was 3%, and the dropping point increasing about 11%. The rheological behaviors of the nanofluids show that the grease with various concentrations of MWCNTs demonstrates non Newtonian behaviors and the results indicated that the shear stress, apparent viscosity and thermal conductivity increase with the increase of volume concentration of MWCNTs to 65%, 52%, and% 56, respectively.

Oils and grease have beneficial effects on moving parts such as connecting rod, gears, shafts, and engine to reduce wear and friction. The properties of lubricants such as tribological and rheological properties are an important role in oils and grease characterization. Nano additives on lubricant oils play an important role in anti-wear; reduce the coefficient of friction and enhance the rheological properties. The Tribological and rheological behavior of base oil 15W50 which have different concentrations of multi-wall Carbon Nanotubes (MWCNTs) (0.5, 1, 1.5, and 2 wt%), and constant amount of graphene nanosheets (GNSs) (0.5 wt%) were investigated. This research is the first one in studying the effect of hybrid nano additives of (MWCNTs) and (GNs) on the tribological and rheological properties of lubricant oils. Tribological characterization was carried out on four ball testing model under different loads (200, 400, 600, and 800 N). The kinematic viscosity, flash point, pour point, and thermal conductivity of nanofluid added 15W50 lubricant are estimated and compared with base oil. The results showed that nano additives improve the wear scar and coefficient of friction by 78% and 48%, respectively. The flash point, thermal conductivity, kinematic viscosity, and pour point, were improved by 15%, 77%, 76.8%, and 20%, respectively compared with the base oil. The hybrid addition of CNTs/GNs nanoparticles enhanced the properties of 15W50 engine oil.