Material jetting (MJT) is a category of additive manufacturing processes where the build material is deposited in the form of individual droplets. MJT has recently been expanded into the field of metal processing due to a potentially high printing speed at low equipment and raw material cost. For full 3D capability, support structures are needed that have to be removed after the print job. We examine water soluble salts and suitable nozzle materials to realise the printing of molten salt in a MJT process. Here, the wetting characteristics of the melt and nozzle are crucial because pronounced wetting is problematic for the ejection of droplets. A sessile-drop contact angle test stand was set up to evaluate the wetting characteristics of three salts or salt mixtures (NaCl, KCl–NaCl and NaCl– $${\hbox {Na}_{2}\hbox {CO}_{3}}$$ ) on six different nozzle materials (various ceramics and graphite), i.e. potential nozzle materials. The results indicate a high wetting tendency of most of the examined samples with the exception of KCl-NaCl on graphite. Application of these materials on a MJT test stand confirm the feasibility of our findings.
Like most additive manufacturing processes for metals, material jetting processes require support structures in order to attain full 3D capability. The support structures have to be removed in subsequent operations, which increases costs and slows down the manufacturing process. One approach to this issue is the use of water-soluble support structures made from salts that allow a fast and economic support removal. In this paper, we analyze the influence of salt support structures on material jetted aluminum parts. The salt is applied in its molten state, and because molten salts are typically corrosive substances, it is important to investigate the interaction between support and build material. Other characteristic properties of salts are high melting temperatures and low thermal conductivity, which could potentially lead to remelting of already printed structures and might influence the microstructure of aluminum that is printed on top of the salt due to low cooling rates. Three different sample geometries have been examined using optical microscopy, confocal laser scanning microscopy, energy-dispersive X-ray spectroscopy and micro-hardness testing. The results indicate that there is no distinct influence on the process with respect to remelting, micro-hardness and chemical reactions. However, a larger dendrite arm spacing is observed in aluminum that is printed on salt.
5 November 2023 in International Journal of Metalcasting
Organically-bound foundry cores are substituted by inorganically-bound cores increasingly. This trend is due to regulatory efforts, workplace safety issues, and increasing costs for waste deposits. Changing the binder system reduces the emissions to mostly water vapor, solving health and safety issues. Yet, the difference in the behavior of the gas phase, namely, the condensation potential of water, changes the casting process drastically. In contrast with the continuous generation and discharge of combustion products in the case of organic binders, water accumulates within the foundry core. Only once the cold spots of the core reach boiling temperature noteworthy amounts of vapor are created, increasing the chance for gas defects of the cast parts. Countermeasures have to be taken when designing the core’s geometry. We conducted the following research to improve the understanding of core gas release and its interactions with the foundry core’s binder content and storage conditions. Both binder content and relative humidity during storage were varied in three steps. Their influence on the core gas amount, time of gas generation, and gas permeability of the cores were investigated. The experiments were performed in the institute’s Induction Analysis Furnace and an aluminum melt bath. We found a strong dependency of storage humidity, further increased by increasing binder content on the gas amount and time of the gas release.
The clogging of piezoelectric nozzles is a typical problem in various additive binder jetting processes, such as the manufacturing of casting molds. This work aims at print head monitoring in these binder jetting processes. The structure-born noise of piezoelectric print modules is analyzed with an Artificial Neural Network to classify whether the nozzles are functional or clogged. The acoustic data are studied in the frequency domain and utilized as input for an Artificial Neural Network. We found that it is possible to successfully classify individual nozzles well enough to implement a print head monitoring, which automatically determines whether the print head needs maintenance.
24 July 2023 in International Journal of Metalcasting
Environmental and work safety aspects necessitate a radical change in the foundry industry. Organic binder systems for foundry sand cores create toxic combustion products and are, therefore, more and more often substituted by inorganic binder systems. While providing an environmental advantage by mainly releasing water vapor, inorganic binder systems impose new challenges for the casting process. The gas release of inorganically-bound foundry cores can lead to increased gas porosity in the cast parts and thus to high scrap rates. The present work aims to gain more understanding of the gas generation and transport in inorganic sand binder systems. We developed a test stand to measure the temperature-dependent core gas release in inorganically-bound foundry cores and their gas permeability. Samples were prepared in a core blowing process and analyzed using the test stand. The measurement results are in good agreement with validation experiments and existing literature.