Bina Hejazi

Ms. Bina Hejazi

Materials testing Institute, University of Stuttgart, Stuttgart, Baden-Württemberg, Germany
orcid
Research Associate and PhD. Candidate at university Stuttgar...

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 April 2024 in Materials
Verified
Journal Article
Open access
PDF file
Bina HejaziBina Hejazi
Bina Hejazi
CLCorinna Luz
Corinna Luz
FGFriedrich Grüner
Friedrich Grüner
JFJuergen Frick
Juergen Frick
HGHarald Garrecht
Harald Garrecht
In the restoration or rehabilitation of traditional buildings, compatible materials with known characteristics must be used. However, the existing literature lacks comprehensive studies on the characterisation of Persian mud–straw plaster, focusing primarily on Persian adobe. Moreover, previous research on Persian adobe has primarily employed XRF and XRD tests, neglecting ion chromatography, moisture sorption isotherm determination, and thermogravimetric analysis with differential scanning calorimetry. Consequently, there is a shortage of information regarding the elemental composition, mineralogical characteristics, moisture sorption behaviour, and thermal properties of Persian mud–straw plaster, as well as Persian adobe bricks. This paper aims to address this research gap by examining historical and new adobe bricks and mud–straw plaster used in Iran, utilising a comprehensive array of analytical techniques. The results from XRF analysis reveal relatively similar chemical compositions across all samples, while XRD analysis indicates predominantly similar mineral phases. Ion chromatography results demonstrate higher conductivity and chloride concentrations in the mud–straw samples than the adobe samples, with higher values for new samples than historical ones. Freshly used straw, clay, or soil may have higher chloride concentrations caused by the arid climate and soil salinisation in the area. Additionally, moisture sorption isotherm determination results show that adobe and mud–straw plaster with a higher salt load of chlorides have significantly higher moisture absorption. The increased straw quantity in the samples increases the moisture content. Furthermore, thermogravimetric analysis and differential scanning calorimetry indicate that, at low heating, adobe and mud–straw plaster lose water due to dehydration, and at high heating, they lose carbon dioxide due to decarboxylation. The comprehensive characterisation of Persian adobe and mud–straw plaster in this study fills a significant gap in the literature and offers invaluable insights for informing restoration and rehabilitation processes, ensuring the compatibility of the materials used.

31 May 2026 in Energies
Verified
Journal Article
Open access
PDF file
Bina HejaziBina Hejazi
Bina Hejazi
AHAndreas Huß
Andreas Huß
JFJuergen Frick
Juergen Frick
HGHarald Garrecht
Harald Garrecht
Accurate knowledge of the thermal transmittance (U-value) of existing building envelopes is essential for reliable energy performance assessment and the planning of energy-efficient refurbishment measures. However, in practice, the material composition of existing walls is often unknown, and installing measurement devices may be restricted due to limited accessibility, the risk of structural damage, or varying on-site boundary conditions. Although several in situ methods for determining the U-value have been proposed in the literature, systematic comparisons of their performance under real environmental conditions remain limited. This lack of comparative evaluation makes it difficult to select the most appropriate method under specific practical constraints. To address this gap, this study presents a comprehensive experimental comparison of four in situ U-value measurement methods applied simultaneously to the same building element under identical real boundary conditions, providing new insights into their accuracy, uncertainty, and practical applicability. In this study, four in situ techniques commonly used to determine the thermal transmittance (U-value) were tested on a double-leaf brick wall at the University of Stuttgart: heat flow meter (HFM), infrared thermography (IRT), infrared thermometer (IRTM), and thermometric method (THM). The measurements were carried out over several days under real boundary conditions, during which air temperature, surface temperature, and heat flux were recorded at regular intervals. The results show that all four techniques can be reliably used under real boundary conditions, with the measured U-values lying within a comparable range. Differences among the methods were observed, largely due to their varying sensitivity to environmental influences and sensor placement. A comparison between the upper and lower parts of the wall indicated that its thermal response is non-uniform, and the observed deviations can be attributed to its inhomogeneous structure. By outlining the strengths and limitations of each technique and comparing their measurement outcomes, this study provides practical guidance for selecting suitable approaches for in situ U-value determination. Furthermore, the findings support future efforts to refine thermal evaluation methods and improve energy performance in existing buildings.

1 November 2020 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
PDF file
Bina HejaziBina Hejazi
Bina Hejazi
NSNayara R. M. Sakiyama
Nayara R. M. Sakiyama
JFJürgen Frick
Jürgen Frick
HGHarald Garrecht
Harald Garrecht
A practical way to reduce energy consumption is to use traditional construction methods and materials. Persian architecture has a long history of constructing energy-efficient and comfortable buildings for the human and has created sustainable cities. Hygrothermal analysis of a building in Yazd, a city in the hot-dry region of Iran, was performed, and the possibility of use of adobe in modern construction for energy-efficient buildings was examined. The aim was to determine the indoor temperature and relative humidity and study its effect using or not using cooling and heating systems. For the simulation, the WUFI + code was used, where internal temperature and relative humidity were determined. Results showed that the use of traditional materials had a considerable effect on reducing internal temperature and humidity fluctuations.