The AQWA software is often used to perform hydrodynamic analysis, and it is highly convenient for performing frequency domain simulations of Pelamis-like wave energy converters. However, hydraulic power take-off (PTO) must be simplified to a linear damping model or a Coulomb torque model when performing a time domain simulation. Although these simulation methods can reduce the computational complexity, they may not accurately reflect the energy capture characteristics of the hydraulic PTO. By analyzing system factors such as the flow and pressure of each branch of the hydraulic PTO, the output torque of the hydraulic cylinder to the buoy, and the electromagnetic torque of the generator, a relatively complete hydraulic PTO model is obtained, and the model is applied to AQWA using the FORTRAN language. Comparing and analyzing the simulation results of the linear damping model, the Coulomb torque model, and the hydraulic PTO, we found that the simulation results obtained by the linear damping model are quite different from those of the hydraulic PTO, while the torque characteristics, kinematic characteristics and energy capture characteristics of the Coulomb torque model are closer to those of the hydraulic PTO model. Therefore, it is more appropriate to simplify hydraulic PTO to a Coulomb torque model based on AQWA.
Several studies have shown that actuation concepts such as Serial elastic actuator (SEA) can reduce peak power and energy consumption in ankle prostheses. Proper selection and design of the actuation concepts is important to unlock the power source potential. In this work, the optimization design, mechanical design, control scheme, and bench experiments of a new powered ankle–foot prosthesis is proposed. The actuation concept of this prosthesis is parallel elastic actuator (PEA) composed of electro-hydrostatic actuator (EHA) as the power kernel and a unidirectional parallel spring as the auxiliary energy storage element. After the appropriate motor and transmission ratio was selected, a dynamic model of the PEA prosthesis was built to obtain the appropriate spring parameters driven by biological data. The design of the hydraulic and mechanical system and the controller were provided for the implementation of the designed system. Bench experiments were performed to verify the performance. The results showed that the designed prosthesis meets the biomechanical dynamics requirements. This result emphasizes the feasibility of the EHA as a power source and actuator and provides new ideas for the design of ankle–foot prostheses.
While powered prosthetic feet with monoarticular actuation allow for the restoration of human ankle biomechanics, gait asymmetries and increased walking effort have been found for transtibial amputees. We hypothesize that this is because of the missing mechanical coupling between the foot and the thigh, which is realized in human legs by the biarticular gastrocnemius (GAS) muscle. This work investigated the effects of a powered prosthetic foot that includes a monoarticular powered prosthetic foot and a biarticular GAS actuator on nine non-impaired subjects while walking on a treadmill. While maintaining total ankle torque, we modulated the torque contribution ratio κ of the GAS actuator to the total ankle torque and recorded kinematics, kinetics and metabolic cost. We found a maximum reduction in metabolic cost by up to 8.8%±4.4% on average for a κ of 0.36±0.09. We attribute this reduction to (a) reduced biological hip work due to energy transfer from the GAS actuator to assist hip flexion, (b) increased inter-leg symmetry of center of mass collision and propulsive work, knee push-off work and step length and (c) increased efficiency of the center of mass movement caused by a reduction in contralateral leg collision work. Our study demonstrates that the biarticular actuator provides an additional degree of freedom that allows for the modulation of human gait biomechanics.
1 September 2019 in IOP Conference Series: Materials Science and Engineering
As a crucial part of micro-satellite, the spatial deployable mechanism has the direct effects on satellite performance and success or failure of flight mission. With requirements of lightless and low cost for satellite, the tape spring hinges are widely used for their simple structural form, high reliability of deployment, high-driving performance and accurate positioning in deployable mechanism. Strain energy stored in the folding process of tape spring hinge is transformed into kinetic energy to achieve the deployment of solar panels. When in full deployment, the tape spring hinge can realize self-locking based on its critical moment. Tape spring is the crucial component of a novel space deployable structure that applied to solar panels. Its full deployment determines the normal function of satellite in space. Mechanical properties, steady-state moment and fatigue life, are observed in folding and deploying processes, which are affected by geometric parameters. Influences of thickness, subtended angle, radius and length on the fatigue life of tape spring are carried out to through numerical simulations so as to ensure a multi folding and deploying cycles for tape spring hinge. Results show that thickness has the greatest influence on the fatigue life, subtended angle and radius are second, and the influence of length on fatigue life is relatively small. On the basis, the optimal model is established based on response surface methodology with the thickness and radius as design variables, steady moment as constraint, and fatigue life as optimization objective. By using genetic algorithm to solve the model, optimal design is obtained within the constraint, and then the optimal design is remodeled and simulated, and the obtained results indicate the accuracy of the optimal design. This research could be a reference for the stability design of space deployable structures.
2 March 2026 in IEEE Robotics and Automation Letters
Hydraulic systems have been widely applied in lower-limb prostheses, primarily for their compact actuation and inherent damping capability. However, when applied to powered prosthetic feet, valves and other damping elements cause unavoidable energy dissipation, thereby constraining their power density. To address this limitation, we propose a valve-less electro-hydrostatic powered prosthetic foot aimed at enhancing power efficiency. In addition, a gas accumulator’s nonlinear elasticity is considered, forming a hydraulic series elastic actuator with passive stiffness comparable to the human ankle during walking. This configuration lowers the motor’s required speed, consequently reducing its actual electrical power. The proposed design was evaluated through a treadmill walking experiment with a non-impaired subject walking at 1.1 m/s. The results showed that the prosthetic foot provided sufficient positive power relative to human reference values. Moreover, the prosthesis achieved a peak output power of 206.3 $\pm$ 15.0 W, while the corresponding motor electrical power was only 147.5 $\pm$ 29.5 W. Our study demonstrates that the electro-hydrostatic system holds significant potential for enhancing the power density of powered prosthetic feet.