Reclaimed Asphalt Pavement (RAP) material mainly consists of removed asphalt concretes from existing infrastructures and, to a minor extent, of wasted or rejected mixes during the production processes. Being composed of two valuable non-renewable resources, i.e., aggregates and bituminous binder, its conscious use can ensure the sustainability of asphalt pavement construction. Thanks to the use of RAP material in new asphalt products, the USA saved 4.1 million tons of virgin binder and 78 million tons of virgin aggregates in 2018. Therefore, the use of RAP for the production of new asphalt formulations at the top of the recycling hierarchy is preferable instead of being down-cycled in low-value applications. The RAP material represents one of the most re-used construction products worldwide; in 2018, approximately 88% wt. and 72% wt. of RAP were used in USA and Europe, respectively, as aggregates for Hot, Warm and Cold Asphalt Mixtures and for unbound layers. Several studies have revealed positive responses of the recycled asphalt mixtures with high or very high content of RAP. However, the common practices of many countries still limit the RAP content to a 15–20% wt., on average, in the recycled asphalt mixes. The amount of RAP in asphalt concretes can be significantly increased by applying good management practices of the RAP, either processed or not, as well as novel production technologies and advanced mix design approaches. This manuscript aims to summarize the state-of-the-art of use of RAP aggregates in new asphalt mixtures. The economic and environmental benefits are also discussed.

Bitumen undergoes ageing, which leads to changes in its chemical and rheological properties, causing it to become harder and more brittle with time. This study aims to compare the effects of different laboratory ageing methods on the chemistry and rheology of three bitumen types: a Pen $40/60$ , a Pen $70/100$ , and a polymer-modified bitumen (PmB). Four ageing protocols were applied: ageing at room temperature, oven ageing, pressure ageing vessel (PAV), and rolling thin-film oven test (RTFOT) combined with PAV ageing. The effects of temperature, pressure, and ageing time were studied using dynamic shear tests and infrared spectroscopy. The results highlight the relationship between chemistry and rheology of bitumen. Bitumen hardening, which was revealed by an increase in complex modulus and a decrease in phase angle, was reflected in the growth of specific chemical functional groups. Among all materials, soft bitumen showed the greater tendency to oxidize. Different behavior was observed for PmB, which presented the highest resistance against oxidation among the studied bitumens, even though the reaction with oxygen caused the deterioration of the added polymer modifiers.

Pavements are an expensive part of transportation infrastructures, as their construction and maintenance require large amounts of resources and materials every year and all over the world. A sustainable solution for considering environmental concerns about roads and pavements, in general, is utilizing recycled materials for their construction. This has been shown to lower the carbon footprint of the construction sector and to result in natural resource conservation, in reduction of harmful emissions and in minimization of overall costs for pavement construction and maintenance. One of the main groups of recycled materials which has attracted much attention since the end of the last century is construction and demolition waste aggregates (CDW). This paper reviews the completed studies referring to the use of the construction and demolition waste aggregates in unbound layers of pavements and compare the in-hand results from various engineering assessments of these aggregates and mixes. A number of tests and evaluations are applied in order to enhance the required quality and durability of the pavements under given traffic volumes traffic loads and climate actions. Today, unbound recycled aggregates (RA) are mainly used in the lower layers, such as subgrade, capping, sub-base and base, but in rural roads they can be adopted also for bound layers, towards the surface of the structure and may be constituents of bound layers and of novel surfacing applications.

One of the applications of recycled aggregates from construction and demolition processes is the construction of embankments, subbases and foundations for roads where unbound materials are used in replacement for natural aggregates. This work focuses on studying the development of the stiffness of recycled materials during construction, as well as how it modifies over time. The study assessed also the correlation between testing systems. A purpose-built experimental embankment with four sections of different recycled materials was built and tested. Fields were made from two structural layers, forming a homogenous thickness of about 80 cm. The compaction and testing took place using the Continuous Compaction Control technique, obtaining bearing capacity records during the embankment construction phases. The structural performance of the embankment was also determined using different types of light-weight deflectometers. The results show that recycled aggregates perform well when properly compacted and may show some positive self-cementing properties.