To enhance peanut sowing depth consistency, an active depth adjustment planter was designed. This study employs inclination and pressure sensors for ridge surface detection, coupled with a hydraulic cylinder and profiling mechanism to dynamically adjust furrow depth according to ground variations. A mathematical model integrating detection, adjustment, and execution processes was established. The control system adopts an improved DLF-Fuzzy PID (double-loop feedback fuzzy PID) control strategy, with co-simulation in MATLAB/AMESIM for performance comparison. The results demonstrate the improved algorithm’s superiority in sowing depth accuracy. Field experiments evaluated three operational parameters (vehicle speed, pressure, and sowing depth) with the qualification rate as the metric. At 50 mm sowing depth and 3 km/h speed, the system achieved a 94.6% dynamic qualification rate and 2.38% maximum depth variation coefficient. Compared with existing methods, this approach enhances sowing depth control effectiveness by 6.05% and reduces variation by 2.85%.
In order to facilitate the peanut plot breeding process, a seed discharger for peanut plot breeding was designed and optimised. Two single stroke cylinders were used for seed replacement and to avoid confusion between different varieties of seeds. The working performance of the seed discharger was simulated by the CFD-DEM method. The simulation results showed that the seed suction hole could adsorb the seeds stably, the adsorption force at the seed suction hole was about 0.02 N, and the seed-clearing time was 0.31 s. When the rotation speed of the seed discharge cylinder was 25 r/min, the diameter of the seed suction hole was 6 mm and the working negative pressure was −5.5 kPa. The developed seed discharger was installed on the test bench to carry out the central composite design experiment, and the test results were analysed and optimised by Design-Expert software. The final parameters of the seed discharger were obtained as follows: rotational speed of the seed cylinder is 25 r/min, the diameter of the seed suction hole is 6 mm, and the working negative pressure is −6 kPa. This indicates that the design of the initial parameters is reasonable. Finally, the seed discharger was tested in the field. The results shown that the 95% confidence intervals for seeding pass rate, multiple-seed rate, and seed missing rate were (88.9557%, 93.1777%), (3.8137%, 6.4597%), and (2.1157%, 5.4777%), respectively, which met the requirements of peanut plot seeding.
A seed discharger for peanut plot breeding was designed and its seed supply, seed carrying, seed discharge and seed clearing processes were analysed. Two single stroke cylinders were used for seed replacement and to avoid confusion between different varieties of seeds. The working performance of the seed discharger was simulated by CFD-DEM mothed. The simulation results showed that the seed section hole could adsorb the seeds stably, the adsorption force at the seed suction hole was about 0.02N, and the seed clearing time was 0.31s, when the rotation speed of the seed discharge cylinder was set to be 25r/min, the diameter of the seed suction hole was set to be 6mm, and the working negative pressure was set to be 5.5kPa. The developed seed discharger was installed on the test bench to carry out the central composite design experiment, and the test results were analysed and optimized by Design-Expert software. The optimal parameters of the seed discharger were obtained as follows: rotational speed of the seed cylinder is 24.38 r/min, the diameter of the seed suction hole is 5.73 mm, and the working negative pressure is -6.15 kPa. Finally, the seed discharger was tested in the field, and the result shown that the seed spacing pass rate was more than 90%, the multiple seeds rate was less than 6%, the seed missing rate was less than 4.5%, and the seed clearing rate was always 100%, which met the requirements of peanut plot seeding.
Higher education institutions are receiving a major facelift due to the adoption of AI and Machine Vision into their smart automation systems. This paper aims to determine the potential impact of the implementation of these systems on the improvement of operational effectiveness, customization of learning, as well as safety. The researchers carried out a thorough literature review of the newer works about AI in the educational process, machine vision algorithms, and architectures of smart automation. Experts' interviews and case studies helped to identify crucial challenges and chances. It is observed that there are various aspects that affect the successful adoption and integration of systems into organizations which include data governance frameworks, standards for interoperability, and the level of stakeholder engagement. This work is significant for the educators, the technology providers, and the government officials who are interested in the performance of AI and machine vision in various educational environments. Высшие учебные заведения претерпевают значительные изменения в связи с внедрением искусственного интеллекта и машинного зрения в свои интеллектуальные системы автоматизации. Цель данной статьи – определить потенциальное влияние внедрения этих систем на повышение операционной эффективности, индивидуализацию обучения, а также безопасность. Исследователи провели тщательный литературный обзор новейших работ об использовании искусственного интеллекта в образовательном процессе, алгоритмах машинного зрения и архитектурах интеллектуальной автоматизации. Интересно с экспертами и тематические исследования помогли выявить важнейшие проблемы и возможности. Отмечается, что существуют различные аспекты, влияющие на успешное внедрение и интеграцию систем в организациях, включая основы управления данными, стандарты функциональной совместимости и уровень вовлеченности заинтересованных сторон. Эта работа важна для преподавателей, поставщиков технологий и государственных служащих, которые заинтересованы в эффективности ИИ и машинного зрения в различных образовательных средах.