After the biomass pretreatment and fermentation processes, the purification step constitutes a major task in bioethanol production processes. The use of membranes provides an interesting choice to achieve high-purity bioethanol. Membrane separation processes are generally characterized by low energy requirements, but a high capital investment. Some major design aspects for membrane processes and their application to the ethanol dehydration problem are addressed in this work. The analysis includes pervaporation and vapor permeation methods, and considers using two types of membranes, A-type zeolite and amorphous silica membrane. The results identify the best combination of membrane separation method and type of membrane needed for bioethanol purification.
1 May 2021 in Journal of Loss Prevention in the Process Industries
The present work aimed to design a separation process for 2-phenylethanol (2-PEA) produced by whey fermentation and to evaluate its economic potential. The separation sequence consisted of a liquid–liquid extraction column followed by two distillation columns for 2-PEA purification and solvent recovery. In addition, the use of ethyl acetate as a solvent for the extraction process was analyzed. The results, aided by the Aspen Plus v.10 process simulator, showed that 2-PEA can be separated with a purity of 96% by weight. The operating cost of the process, estimated at USD 22.70 per kilogram, shows that the separation alternative developed in this work has a high economic potential. The use of ethyl acetate as a solvent was found to efficiently remove 2-PEA from the fermentation mixture. From a process safety analysis point of view, the use of a bioprocess safety index developed in this work identified the separation process sections that could require special attention as part of the safety engineering stage of the process implementation.
In some fermentation systems, whey components (lactose, proteins and minerals) can produce isopentyl acetate (IA). An analysis of the best conditions for IA production with Kluyveromyces marxianus was developed in this work. The experiment design was two-factor and three-level design based on a response surface methodology (RSM) using Design-Expert® software. The analysis of anomeric protons by nuclear magnetic resonance (1H-NMR) showed 81.25% of β lactose content. This characteristic favored the production of IA. The maximum output (Mp) of IA, determined by gas chromatography, was 9.52 g/L (p < 0.05). The central composite design (CCD) was used to perform the factor analysis. Results showed that concentrations of 0.03 (g/L) ammonium sulphate and 0.3 (v/v) of isoamyl alcohol are the best conditions for a maximum rate of IA production. The production of IA can reduce the discharge of whey, allowing its reuse and revaluation.
In many countries, whey from the dairy industry is an abundant waste that generates an important environmental impact. Alternative processes to use the whey and minimize the environmental impact are needed. This work considered six formulations with different ammonium sulfate and L-phenylalanine (L-Phe) concentrations to produce bioethanol in sweet whey fermentation by Kluyveromyces marxianus. The results showed a maximum bioethanol concentration equal to 25.13 ± 0.37 g L−1 (p < 0.05) for formulation F6, with 1 g L−1 of L-Phe and 1.350 g L−1 of ammonium sulfate (96 h). For these conditions, the chemical oxygen demand removal percentage (CODR%) was 67%. The maximum CODR% obtained was 97.5% for formulation F3 (1 g L−1 of L-Phe) at 96 h; however, a significant decrease in bioethanol concentration (14.33 ± 2.58 g L−1) was observed. On the other hand, for formulation, F3, at 48 h of fermentation time, a bioethanol concentration of 23.71 ± 1.26 g L−1 was observed, with 76.5% CODR%. Based on these results, we suggest that the best conditions to obtain a significant bioethanol concentration and CODR% value are those used on the configuration F3 at 48 h.