Claudia Irina Săvescu

Dr. Claudia Irina Săvescu

Automation and Electrical Engineering, Romanian Research and Development Institute for Gas Turbines, Bucharest, Bucureşti, Romania
+1
orcid
Scientific Researcher III at NRDI Gas Turbines COMOTI & Scie...

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 August 2019
Verified
Conference Paper
Open access
PDF file
Claudia Irina SăvescuClaudia Irina Săvescu
Claudia Irina Săvescu
Iulian VlăducăIulian Vlăducă
Iulian Vlăducă
DIDan Ionescu
Dan Ionescu
VPValentin Petrescu
Valentin Petrescu
FNFilip Niculescu
Filip Niculescu
MHMihai Hanek
Mihai Hanek
Compressed Air Energy Storage (CAES) installations are used for storing electrical power, under the form of potential energy from compressed air. The heat generated during compression can be stored to improve the efficiency of compression-expansion cycle. The solution presented consists of a 100 kW screw compressor driven by a 110 kW asynchronous three-phase motor. The compressor supplies air into vessels which store it until a high electrical energy demand arises. At that time, the compressed air is released into a 132 kW screw expander whose shaft spins a 132 kW asynchronous generator, producing electric power and supplying it into the electrical grid. Before expansion, the air must be preheated in order to avoid the freezing of expansion equipment. If the heat generated during compression is used for air preheating before expansion, the process is adiabatic. A demonstrative model of the installation is currently being developed, with the expander part being completed so far. The maximum power to be produced was calculated to be around 100 kW. During expander commissioning tests with air supply from a 250 kW high pressure compressor, a maximum generated power of 49.7 kW was attained, expected to be higher when releasing air from the reservoirs.

20 August 2019
Verified
Conference Paper
Open access
PDF file
Claudia Irina SăvescuClaudia Irina Săvescu
Claudia Irina Săvescu
DCDaniel Comeagă
Daniel Comeagă
The paper aims to assess and improve the performances of a multilayer piezoelectric MEMS device for vibrations harnessing. Two operating modes are possible: at resonance and outside resonance. In some applications it is not possible to operate at resonance, functioning being mostly at low frequencies in a quasi-static regime. An Euler-Bernoulli classic beam theory mathematical model was studied for estimating the behaviour of multilayer piezoelectric generators, in terms of deflection and voltage, at functioning under resonance frequency. The analytical results were compared with the finite element method simulation in COMSOL Multiphysics. The main goal of this study is to obtain an accurate model for engineering design purposes, with simple analytical equations and ease of use, but with predictable errors. The study proved the usefulness of the derived model but also its limitations. It also proves the need to improve the model using plate theory, for sensors with high width/height ratio.

1 December 2020 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
Claudia Irina SăvescuClaudia Irina Săvescu
Claudia Irina Săvescu
CCC D Comeagă
C D Comeagă
MUM N Uddin
M N Uddin
RHR D Hriţcu
R D Hriţcu
VRV L Ringheanu
V L Ringheanu
The paper studies the influence of tip curvature on the electrical response of a piezoelectric energy harvester, on a direction other than the charge generation one. Finite element analyses were conducted for the given piezoelectric transducer, which show an increase in the voltage output if blocking the tip curvature on yOz plane between two bars, leaving free only the deflection on xOz plane. The comparison was made between cantilever tip constrained with bars and cantilever with an equivalent proof mass respectively. The simulations in COMSOL Multiphysics are furthermore validated by experimental laboratory tests, confirming the increase of the electric output potential with ~8%. This occurs due to inducing higher stress into the structure by blocking its tip curvature. The frequency response, defined between base excitation and the output voltage, was determined using an impedance analyser. The bars also act as a proof mass, thus decreasing the resonant frequency optimally down to the vibration frequencies of an oil-free compressor’s downstream pipe on which the transducer will be mounted in order to harness the inherent vibrations and subsequently power wireless sensors.

6 January 2022 in MATEC Web of Conferences
Verified
Journal Article
Open access
PDF file
CNCristian Nechifor
Cristian Nechifor
Claudia Irina SăvescuClaudia Irina Săvescu
Claudia Irina Săvescu
ASAdrian Stoicescu
Adrian Stoicescu
DLDaniel Lale
Daniel Lale
MVMirela Vasile
Mirela Vasile
The paper presents an automation system dedicated to oil & gas machinery applications, such as electrical gas compressors. The future aim is to introduce it into the Romanian oil & gas industry. The system consists of a low size cabinet and its dependencies, which can be used in ATEX Zone 2. The electronic equipment is dimensioned and chosen according to the standards in force, so that the limited current and voltage requirements for methane gas to be met. The key feature is that this system complies with all ATEX standards for Zone 2. Moreover, it can also be a mobile and modular solution if needed, for a versatile and easy use in proactive monitoring of multiple locations across various compressor plants. The design, wireless transmission and possible implementation of this cabinet are presented. Remote data transmission via Wi-Fi and RS-485 communication interfaces between the devices is considered, due to several advantages: mobility, versatility, wide compatibility, environmentally friendly, as well as higher resources efficiency (reducing time and costs).

27 May 2021
Verified
Conference Paper
Closed access
Iulian VlăducăIulian Vlăducă
Iulian Vlăducă
Claudia Irina SăvescuClaudia Irina Săvescu
Claudia Irina Săvescu
MVMirela Letitia Vasile
Mirela Letitia Vasile
GBGeorge Iulian Balan
George Iulian Balan
ASAdrian Savescu
Adrian Savescu
RCRazvan Ciobanu
Razvan Ciobanu
Nowadays, automation systems for naval propulsion groups with gas turbines use programmable logic controllers for a precise and reliable control. The automation system is designed so as to be able to connect using signal cables to the transducers monitoring the engine’s parameters, via adapters, so that the command and regulation functions to be fully automatized. These signals are managed by means of the software program implemented in the PLC, and subsequent data acquisition. One of the important problems is the available resource of the propulsion group, until capital repair is required. The remaining lifetime depends on the operating regimes of the gas turbine engine. This problem is more pronounced in the propulsion groups equipping navy ships, where the dynamic regimes of gas turbine engines are much more demanding, and hence the pre-established operating limits may be exceeded. The automation configuration presented herein ensures the accurate computation and precise control of essential parameters for which the direct measurement is not possible using transducers. These parameters are the exhaust gas temperature, the power developed by the engine and implicitly the torque developed at propeller shaft.

1 March 2019
Verified
Conference Paper
Closed access
Claudia Irina SăvescuClaudia Irina Săvescu
Claudia Irina Săvescu
CCConstantin Daniel Comeaga
Constantin Daniel Comeaga
The purpose of the paper is to evaluate to what extent a simplified mathematical Euler-Bernoulli model can be used for assessing the parameters of piezoelectric stratified structures. A generalized Euler-Bernoulli model is presented, applied to a composite beam structure integrating piezoelectric layers. The model was particularised for a cantilever beam, fixed constrained at one end and with actuation at the other. The linearity conditions of the model have been determined, being applied for the study of structures with two active layers and a central resistance layer. The values obtained for beam tip deflection and mechanical stress are compared to several FEM models of the multilayer beam. The parallel study was conducted in order to estimate the correctness of the analytic results and to see if this broadly used model is reliable enough to evaluate accurately the parameters of a three-layer piezoelectric cantilever beam.