The use of mixed microbial cultures (MMC) and organic wastes and wastewaters as feed sources is considered an appealing approach to reduce the current polyhydroxyalkanoates (PHAs) production costs. However, this method entails an additional hurdle to the PHAs downstream processing (recovery and purification). In the current work, the effect of a sodium hypochlorite (NaClO) pre-treatment coupled with dimethyl carbonate (DMC) or chloroform (CF) as extraction solvents on the PHAs recovery efficiency (RE) from MMC was evaluated. MMC were harvested from a sequencing batch reactor (SBR) fed with a synthetic prefermented olive mill wastewaster. Two different carbon-sources (acetic acid and acetic/propionic acids) were employed during the batch accumulation of polyhydroxybutyrate (PHB) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) from MMC. Obtained PHAs were characterized by 1H and 13C nuclear magnetic resonance, gel-permeation chromatography, differential scanning calorimetry, and thermal gravimetric analysis. The results showed that when a NaClO pre-treatment is not added, the use of DMC allows to obtain higher RE of both biopolymers (PHB and PHBV), in comparison with CF. In contrast, the use of CF as extraction solvent required a pre-treatment step to improve the PHB and PHBV recovery. In all cases, RE values were higher for PHBV than for PHB.
15 July 2016 in IOP Conference Series: Materials Science and Engineering
Starch is one of the most abundant biopolymer in nature. It has been primarily used as a thickener in the food industry. Starch is found in greater amounts in the potato tubers, which is one of the largest food productions in the region of Boyacá-Colombia. Thus, potatoes are a viable source of starch. The main objective of this study is the preparation and characterization of native starch´s microfiber by electro wet-spinning technique. The parameters that were changed for each treatment were as follows: the amount of potential applied to the solution, the distance between the needle and the collector and the rate of injection of the solution in order to determine the physical and chemical properties of the membranes, conformed by potatoes starch microfiber. Diverse instrumental analysis techniques were applied. They were: Scanning Electron Microscopy (SEM) to determine the morphologies and diameters of microfibers, Fourier Transform Infrared Spectroscopy (FTIR) to determine the chemical changes, Thermogravimetric Analysis (TGA) and Differential Calorimetry Scanning (DSC) to obtain the thermal transitions and the temperatures of useful. The microfibers were analysed in order to determine their structural properties and thus define the range of application. In conclusion, potatoes starch microfibers were obtained with average diameters of 15, 17, 23 and 25 micrometres, besides the fibers presented a degradation temperature of 304 °C, indicating that fibers are available with diameters of small scale, with good thermal properties. This study will enable the implementation of the microfibers to obtain bio packaging for food products and other applications.
Most electrospun scaffolds for bone tissue engineering typically use hydroxyapatite (HA) or beta tricalcium phosphate (β-TCP). However, the biological activity of these crystalline compounds can be limited due to their low solubility. Therefore, amorphous calcium phosphate (ACP) may be an alternative in bone repair scaffolds. This study analyzes the morphology, porosity, mechanical strength, and surface chemistry of electrospun scaffolds composed of polylactic acid and collagen integrated with hydroxyapatite (MHAP) or amorphous calcium phosphate (MACP). In addition, the in vitro biocompatibility, osteogenic differentiation, and growth factor production associated with bone repair using human Wharton’s jelly-derived mesenchymal stem cells (hWJ-MSCs) are evaluated. The results show that the electrospun MHAP and MACP scaffolds exhibit a fibrous morphology with interconnected pores. Both scaffolds exhibit favorable biocompatibility and stimulate the proliferation and osteogenesis of hWJ-MSCs. However, cell adhesion and osteocalcin production are greater in the MACP scaffold compared to the MHAP scaffold. In addition, the MACP scaffold shows significant production of bone-repair-related growth factors such as transforming growth factor-beta 1 (TGF-β1), providing a solid basis for its use in bone tissue engineering.
Currently, research on composite materials derived from natural fibers and agro-industrial waste has generated industrial proposals for producing useful materials with sufficient mechanical strength for applications involving the reuse of waste for secondary purposes. The objective of this study was to determine the influence of fiber content on the final tensile strength of the composite material, serving as a reference for the manufacture of plates. To achieve this, high-density polyethylene (HDPE) composites reinforced with short banana fibers were prepared using a blade mill and hot compression molding techniques. Two levels of short banana fiber content—10% and 20% by weight—were used, along with two types of HDPE: virgin and recycled. We evaluated the effect of adding short banana fibers on the mechanical properties of the composite, specifically tensile strength, according to the ASTM D638 standard for polymeric materials. These results were correlated with the structural properties obtained through morphological, chemical, and thermal characterization of the developed materials. The mechanical evaluation results showed that the tensile strength and elastic modulus depend on the short banana fiber content and the type of high-density polyethylene. Thermogravimetric analysis revealed that the composites decompose faster than the pure polymers (virgin and recycled HDPE). Based on these findings, the composite material prepared under optimal conditions is recommended for use in walls or construction boards where high tensile strength is not critical, due to the decreased mechanical properties resulting from the incorporation of agro-industrial waste.
Given the current situation we face regarding climate change, one of the greatest and most critical concerns is related to the reduction in the bee population. This population largely depends on beekeeping production units around the world. However, these production units also face great challenges in the construction of beehives, as pine word generally deteriorates within a period of five years or less. This relatively rapid deterioration has both economic and environmental repercussions, which may affect the economic sustainability of the beekeeping system. The objective of this research was the production and subsequent evaluation of the durability of alternative composite materials that can be used in beehive construction. The materials are based on high-density polyethylene and agro-industrial residues (fique fiber, banana fiber, and goose feathers) from the Boyacá region of Colombia. The composite materials studied in the present study were exposed to xylophagous fungi for 90 days, at constant humidity and under controlled temperature conditions that are conducive to fungi proliferation. The results showed that composite materials that include fique fibers are the most promising substitute for wood in the construction of beehives. Indeed, these materials were shown to be 80% more resistant to pathogen attack and durable weight loss than pine wood. These durability results may be of great importance for future implementation in beekeeping production units. They have the potential to impact not only the sustainable development of rural communities, but also to make a great ecological contribution by reducing the need to cut down trees while maintaining the health of beehives.
Sugarcane bagasse (SCB) is an abundant by-product of sugar refining that can be utilized as a raw material for cellulose isolation for several industrial applications. Electrospinning has garnered attention in recent years because it allows the preparation of cellulosic materials with unique properties. In this study, cellulose was isolated from sugarcane bagasse and acetylated to fabricate fine acetate cellulose fibers through electrospinning. Subsequently, the electrospun fibers were deacetylated and cationized in order to produce functionalized materials with potential textile applications. The functional fibers were colored with an anionic dye (vinyl sulfone) with and without the presence of salt and were evaluated according to dye fixation, color attributes, morphological characteristics, and thermal stability. Cationic cellulose fibers that were dyed without added salt were found to be brighter and demonstrated better color fixation than those with added salt. In addition, morphological analysis performed using scanning electron microscopy demonstrated that cationized fibers dyed without added salt were better preserved at this stage. The cationic fiber also evidenced a high-temperature resistance, exhibiting a degradation temperature above 236 °C. The results suggest that cellulose fibers dyed in this manner can potentially be considered for use in textile applications due to their suitable dye fixation and tunable porosity (i.e., breathability).