Elena Jasiuniene

Prof. Elena Jasiuniene

Kaunas University of Technology
orcid

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 September 2010 in Journal of the European Academy of Dermatology and Venereology
Verified
Journal Article
Closed access
PDF file
DJD Jasaitiene
D Jasaitiene
SVS Valiukeviciene
S Valiukeviciene
GLG Linkeviciute
G Linkeviciute
RRRenaldas Raisutis
Renaldas Raisutis
EJElena Jasiuniene
Elena Jasiuniene
RKRymantas Kazys
Rymantas Kazys

1 May 2019 in Ultrasonics
Verified
Journal Article
Closed access
EJElena Jasiuniene
Elena Jasiuniene
LMLiudas Mažeika
Liudas Mažeika
Vykintas SamaitisVykintas Samaitis
Vykintas Samaitis
VCVaidotas Cicėnas
Vaidotas Cicėnas
DMDavid Mattsson
David Mattsson

27 September 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
BYBengisu Yilmaz
Bengisu Yilmaz
AAAadhik Asokkumar
Aadhik Asokkumar
EJElena Jasiuniene
Elena Jasiuniene
RKRymantas Kazys
Rymantas Kazys
The objective of this study is to compare the performance of different ultrasonic non-destructive testing (NDT) techniques for bonding quality evaluation. Aluminium-epoxy-aluminium single lap joints containing debonding in the form of release film inclusions have been investigated using three types of ultrasonic NDT methods: contact testing, immersion testing, and air-coupled testing. Apart from the traditional bulk wave ultrasound, guided wave testing was also performed using air coupled and contact transducers for the excitation of guided waves. Guided wave propagation within adhesive bond was numerically simulated. A wide range of inspection frequencies causing different ultrasonic wavelengths has been investigated. Average errors in defect sizing per ultrasonic wavelength have been used as a feature to determine the performance of each ultrasonic NDT technique. The best performance is observed with bulk wave investigations. Particularly, the higher frequencies (10–50 MHz) in the immersion testing performed significantly better than air-coupled testing (300 kHz); however, air coupled investigations have other advantages as contactless inspection. Whereas guided wave inspections show relatively lower accuracy in defect sizing, they are good enough to detect the presence of the debonding and enable to inspect long range. Even though each technique has its advantages and limitations, guided wave techniques can be practical for the preliminary in-situ inspection of adhesively bonded specimens.

1 February 2022 in Composite Structures
Verified
Journal Article
Closed access
MRMarius Rimašauskas
Marius Rimašauskas
EJElena Jasiuniene
Elena Jasiuniene
TKTomas Kuncius
Tomas Kuncius
RRRūta Rimašauskienė
Rūta Rimašauskienė
VCVaidotas Cicėnas
Vaidotas Cicėnas

8 September 2020 in Sensors
Verified
Journal Article
Open access
PDF file
BYBengisu Yilmaz
Bengisu Yilmaz
ABAbdoulaye Ba
Abdoulaye Ba
EJElena Jasiuniene
Elena Jasiuniene
HBHuu Kien BUI
Huu Kien BUI
GBGérard Berthiau
Gérard Berthiau
This work aims to compare quantitatively different nondestructive testing (NDT) techniques and data fusion features for the evaluation of adhesive bonding quality. Adhesively bonded composite-epoxy single-lap joints have been investigated with advanced ultrasonic nondestructive testing and induction thermography. Bonded structures with artificial debonding defects in three different case studies have been investigated: debonding with release film inclusion, debonding with brass film-large, debonding with brass film-small. After completing preprocessing of the data for data fusion, the feature matrices, depending on the interface reflection peak-to-peak amplitude and the principal component analysis, have been extracted from ultrasonic and thermography inspection results, respectively. The obtained feature matrices have been used as the source in basic (average, difference, weighted average, Hadamard product) and statistical (Dempster–Shafer rule of combination) data fusion algorithms. The defect detection performances of advanced nondestructive testing techniques, in addition to data fusion algorithms have been evaluated quantitatively by receiver operating characteristics. In conclusion, it is shown that data fusion can increase the detectability of artificial debonding in single-lap joints.

24 February 2021 in Materials
Verified
Journal Article
Open access
PDF file
AAAadhik Asokkumar
Aadhik Asokkumar
EJElena Jasiuniene
Elena Jasiuniene
RRRenaldas Raisutis
Renaldas Raisutis
RKRymantas Kazys
Rymantas Kazys
This article compares different air-coupled ultrasonic testing methods to characterize impact-type defects in a pultruded quasi-isotropic glass fiber-reinforced plastic (GFRP) composite plate. Using the air-coupled transducers, comparisons among three methods were performed, namely, bulk-wave through transmission, single-side access using guided waves, and ultrasonic-guided wave tomography. The air coupled through transmission technique can determine the size and shape of impact-type defects with a higher resolution, but with the consequence of time consumption and, more importantly, the necessity of access to both sides of the sample. The guided wave technique on the other hand, allows a single-side inspection and is relatively fast. It can be used to determine the size of the defect using ultrasonic B-scan, but the exact shape of the defect will be compromised. Thus, in this article, to determine the shape of the defect, application of the parallel beam tomographic reconstruction technique using guided Lamb waves is demonstrated. Furthermore, a numerical finite element simulation was performed to study the effects of guided wave propagation in the composite sample and interaction with the internal defect. Lastly, the results from the experiments of different techniques were compared according to possibilities of defect sizing and determination of its shape.