Despite low energy and fuel consumption levels in the rail sector, further improvements are being pursued by manufacturers and operators. Their primary efforts aim to reduce traction energy demand, replace diesel, and limit the impact of electrified overhead infrastructures. From a system‐level perspective, the integration of alternative energy sources on board rail vehicles has become a popular solution among rolling stock manufacturers. Surveys are made of many recent realizations of multimodal rail vehicles with onboard electrochemical batteries, supercapacitors, and hydrogen fuel cell systems. The ratings, technical features, and operating data of onboard sources are gathered for each application, and a comparison among different technologies is presented. Traction system architectures and energy‐control strategies of actual multimodal units are explored and compared with literature research. Moreover, the maturity and potential of recent technologies and alternative topologies of power converters for multimodal traction systems are discussed. Ultimately, onboard storage systems are compared with other solutions for energy‐saving and catenary‐free operation, with particular focus on their current techno‐economic attractiveness as an alternative to diesel propulsion.
13 May 2022 in IEEE Transactions on Transportation Electrification
The need for decarbonization has increased the interest in alternative propulsion systems for light rail vehicles, including fuel cells, batteries, and supercapacitors. These sources and storage devices can also be used in combination with an external supply to enable operation on both electrified and nonelectrified tracks. In traditional architectures, the sources are connected via dc/dc converters to a common dc-link that feeds the motor drives. This article addresses a new configuration where an NPC-based multisource inverter (MSI) is used for the integration of the dc sources to the traction motors in a single stage. First, a thorough analysis of the converter’s operation is carried out with reference to its state-of-the-art control. The conditions for full control of the dc sources and traction motors over the entire vehicle speed profile are derived. Second, a novel modulation technique is proposed to complement the baseline control and enable the stationary charging of the energy storage from the electrified line through the converter. Thus, the MSI can be operated to match all the functionalities of conventional multimode architecture, with the advantage of the reduced number of power converters. Validations are carried out by means of simulations and extensive experiments on a laboratory test bench.
8 June 2022 in IEEE Journal of Emerging and Selected Topics in Power Electronics
The concept of a multi-source inverter based on NPC topology was recently introduced for hybrid electric powertrains to connect several DC sources to the traction load in a single conversion stage without magnetics. This work proposes a new modulation algorithm that integrates the tasks of DC currents and AC voltages control at level of pulse-width modulation by means of the space-vector formalism. The proposed algorithm allows the multi-source inverter to have full control of the DC input currents and fundamental AC output voltages and enables a higher number of feasible operating modes, including load power sharing between sources and controlled recharging of one source from the other, both in motion and at standstill. Hence, improved control capability of the load and sources is achieved with respect to the state-of-literature modulation approach. To validate the proposed modulation under different operating conditions, steady-state and dynamic tests are performed on a small-scale traction system fed by a primary DC supply and a battery pack. The results are compared with those of the baseline control approach and show that the proposed technique improves the smoothness and flexibility of the control action, reduces the distortion of currents and voltages, while ensuring the same converter efficiency.
The paper firstly summarizes a simple analytical model of the air gap flux-density distribution for isotropic permanent magnet (PM) synchronous machines, in the presence of static eccentricity. The model was proposed by the authors in a previous paper and is based on an efficacious analytical expression of the variable length of air gap magnetic field lines which occur in eccentric brushless machines with surface-mounted permanent magnets. The approximate expression of the air gap field makes it possible to achieve a mathematical model with concentrated parameters close to that of a PM machine without eccentricity. The expression of the armature voltages and electromagnetic torque are found, also with reference to steady-state operating conditions at fixed rotor speed and impressed currents. The differences introduced by the considered type of eccentricity are evaluated and highlighted especially with reference to the air gap inductance and to waveforms and frequency spectra of voltages and shaft torque. Numerical results in a case-study of an 8-pole, 110 kW PM motor are compared to those obtained by using finite element analysis.
The paper deals with static eccentricity in synchronous PM motors with surface mounted magnets. Simple analytical expressions are proposed for the evaluation of the length of stator and rotor magnetic field lines in the air-gap as a function of rotor eccentricity. By means of some appropriate considerations, the analytical expressions of the flux-density distribution of armature and rotor across the air-gap is yield. They allow us to point out a mathematical model of the machine in terms of concentrated parameters. The model is then used in order to evaluate the variations that can occur in the armature currents or in some characteristic parameters of the machine in steady-state operating conditions, with respect to the case without eccentricity.