Sustainable development of the agricultural industry, in particular, the production of milk and feed for farm animals, requires accurate, fast, and non-invasive diagnostic tools. Currently, there is a rapid development of a number of analytical methods and approaches that meet these requirements. Infrared spectrometry in the near and mid-IR range is especially widespread. Progress has been made not only in the physical methods of carrying out measurements, but significant advances have also been achieved in the development of mathematical processing of the received signals. This review is devoted to the comparison of modern methods and devices used to control the quality of milk and feed for farm animals.
Feeding cattle on livestock farms is a labor-intensive operation that requires considerable capital investments to purchase equipment and cover labour costs. The global trends in developing technological equipment for feeding cattle include the robotization of various processes. The operation of feed pushing on the feeding table is an integral part of the feeding process, which has a significant impact on livestock productivity. This study concentrates on the simulation modeling of a feed pusher robot using Simulink tools in the Matlab environment to facilitate robot modernization or optimize the final cost for artificial testing of typical system elements and reduce production costs. Based on a simulation model, an experimental sample was designed with a controlled dispenser of feed additives, which can significantly facilitate the feeding process and optimize the dosing of concentrated additives.
A new calibration procedure, known as mapping conditional-calibration laser-induced breakdown spectroscopy (LIBS), has been suggested to improve analysis results for heterogeneous samples. The procedure is based on LIBS elemental mapping, followed by signal conditioning in every sampling spot to skip signal outliers, then by finalizing the calibration curve construction. The suggested mapping conditional calibration procedure was verified for zinc analysis in soybean grist samples. The laser parameters correspond to those of the hand-held LIBS instrument in order to estimate the influence of sample surface heterogeneity under on-site analysis conditions. The laser spot (60 μm) was equal to or smaller than the typical size of grist particles (40–500 μm) but laser crater dimensions were significantly greater and varied widely (150–450 μm). The LIBS mapping of different spectral signals (atomic and ionic lines for major and minor components) was achieved. Elemental maps were normalized to achieve signal maps that were conditionally spotted to skip signal outliers. It was demonstrated that the suggested mapping conditional-calibration LIBS provided 15 ppm RMSECV for zinc determination in heterogeneous samples, which is typical for agricultural products.
Practical experience demonstrates that the development of agriculture is following the path of automating and robotizing operational processes. The operation of feed pushing in the feeding alley is an integral part of the feeding process and significantly impacts dairy cattle productivity. The aim of this research is to develop an algorithm for automatic positioning and a mobile remote-control system for a wheeled robot on a dairy farm. The kinematic and dynamic motion characteristics of the wheeled robot were obtained using software that allows simulation of physical processes in an artificial environment. The mobile application was developed using Swift tools, with the preliminary visualization of interfaces and graphic design. The system uses technical vision based on RGB cameras and programmed color filters and is responsible for the automatic positioning of the feed-pusher robot. This system made it possible to eliminate the inductive sensors from the system and suspend the labor effort required for assembling the contour wire of the feed alley. By assessing the interaction between the mobile app and the feed pusher via the base station connected to the Internet and located on the farm, the efficiency and accuracy of the feedback was measured. Furthermore, remote changes in the operating regime of the robot (start date) were proven to be achievable, and the productiveness of the food supplement dispenser also became manageable.
The article examines existing methods for assessing the homogeneity of feed mixes in the feed industry and agriculture. As an alternative to existing approaches, the authors offer a low-cost online technology to assess the homogeneity of feed. The feedstuff under study includes feed mixes for cattle or compound feed consisting of naturally-grown feed (green mass of freshly cut grass, haylage, corn silage, etc.) and concentrated components (grain milling, sunflower, and soybean meal). The proposed method based on an RGB camera, a diode lamp, filters, and software is approved by a preliminary study of the physical properties of feed mix components by Specim IQ hyperspectral camera and revealing characteristics of light absorption of each type of components (concentrated/natural origin). The article presents a method of processing a feed mix image fixed by an RGB camera through light filters using Matlab Image Processing Toolbox tools, namely, a Color Thresholder app and Image Region Analyzer app.
25 November 2019 in Machinery and Equipment for Rural Area