Berry fruits are well recognized for health-promoting constituents due to their properties of free radical scavengers which confer antioxidant activity against cellular oxidation reactions. Elderberry fruit contains one of the highest levels of anthocyanins. The objective of this work was to evaluate the storage stability of total monomeric anthocyanins, cyanidin-3-glucoside (one of two major anthocyanins in elderberry), and color parameters in freeze-dried elderberry encapsulated with a low proportion of different carriers (Maltodextrin, Capsul™, Promitor ™, and κ-carrageenan). Encapsulated samples were stored at two different water activities (aw) 0.10–0.20 and 0.43 at 38 ℃ for 90 days and evaluated for the content of monomeric anthocyanins, cyanidin-3-glucoside, color parameters, and physical characteristics. Freeze-dried powders remained free-flowing during storage at 38 ℃ with aw 0.12–0.20, but agglomeration occurred at aw = 0.43. Total anthocyanins and color parameter a* (redness) remained unchanged during storage at the lower aw. Glass transition temperatures (Tg) were determined and mostly correlated with observed physical phenomena. The powders had a very high total monomeric anthocyanin contents as high as 13 mg/g (cyanidin-3-glucoside). The addition of encapsulants in low proportions allowed the researchers to obtain elderberry powders with a very high concentration of total monomeric anthocyanins. aw plays a key role in all stability parameters studied.
The enforcement of a global hydrofluorocarbon (HFC) refrigerant phase down led to the introduction of hydrofluoroolefins (HFOs) as a low Global Warming Potential (GWP) substitute, given their low atmospheric lifetime. However, to this date it is not fully clear the long‐term atmospheric fate of HFOs primary degradation products: trifluoro acetaldehyde (TFE), trifluoro acetyl fluoride (TFF), and trifluoroacetic acid (TFA). It particularly concerns the possibility of forming HFC‐23, a potent global warming agent. Although the atmospheric reaction networks of TFE, TFF, and TFA have a fair level of complexity, the relevant atmospheric chemical pathways are well characterized in the literature, enabling a comprehensive hazard assessment of HFC‐23 formation as a secondary HFO breakdown product in diverse scenarios. A lower bound of the HFOs effective GWP in a baseline scenario is found above regulatory thresholds. While further research is crucial to refine climate risk assessments, the existing evidence suggests a non‐negligible climate hazard associated with HFOs.
The influence of the synthesis procedure of supported Prussian blue nanoparticles (PBNP) on their activity and stability as a Fenton-type catalyst is studied. Hence, two catalysts are synthesized by adsorbing onto a support of PBNP formed ex situ through the reaction between FeCl3 and K3Fe(CN)6 using H2O2 as reducing agent, and following different washing protocols. A third catalyst is prepared through a two-step impregnation process with FeCl3 and K4[Fe(CN)6] aqueous solutions. The catalysts are tested in the orange G Fenton-type oxidation. The fresh and used catalysts are characterized by BET surface area, SEM, EDS, TEM, Mössbauer spectroscopy, total iron content and UV-vis spectrophotometry. It is demonstrated that under the synthesis conditions employed, the “insoluble” form of Prussian blue is promoted in the ex situ procedure, whereas the two-step impregnation process leads to the “soluble” Prussian blue formation. The washing of the just-prepared catalysts at the reaction temperature helps in eliminating the unreacted species. Those catalysts based on “insoluble” Prussian blue nanoparticles exhibit better behaviour in terms of stability. Significant removals are attained (100% azo dye, 60% TOC), at pH = 3, 343 K after thirteen successive cycles of 300 min. The best catalyst displays the smallest amount of total “free” Fe leached without releasing PBNP, ferrocyanide or ferricyanide ions into the reaction media. Reversible adsorption–desorption of organic intermediates avoids the loss of activity due to blockage of sites and/or pores.
This work is focused on optimising a low-temperature delignification as holocellulose purification pretreatment of Platanus acerifolia leaf waste for second-bioethanol production. Delignification was accomplished by acid-oxidative digestion using green reagents: acetic acid and 30% hydrogen peroxide 1:1. The effect of reaction time (30–90 min), temperature (60–90 °C), and solid loading (5–15 g solid/20 g liquid) on delignification and solid fraction yield were studied. The process parameters were optimised using the Box–Behnken experimental design. The highest attained lignin removal efficiency was larger than 80%. The optimised conditions of delignification, while maximising holocellulose yield, pointed to using the minimum temperature of the examined range. Analysis of variance on the solid fraction yield and the lignin removal suggested a linear model with a negative influence of the temperature on the yield. Furthermore, a negative effect of the solid loading and low effect of temperature and time was found on the degree of delignification. Then the temperature range was extended back to 60 °C, providing 71% holocellulose yield and 70% while improving energy efficiency by working at a lower temperature. Successful lignin removal was confirmed using confocal laser scanning microscopy. As evaluated by scanning electron microscopy, the solid structure presented an increased exposition of the cellulose fibre structure.
Dark fermentation is a hydrogen generating process carried out by anaerobic spore-forming bacteria that metabolize carbon sources producing gas and short-chain acids. The process can be controlled, and the hydrogen harvested if bacteria are grown in a reactor with favorable conditions. In this work, bacteria selected from natural sources were grown with a defined culture media, while pH was monitored, with the aim of relating the amount of generated hydrogen to the increase in hydron ion concentration. Therefore, a model based on the acid-base species mass balance is proposed and solved to estimate the lag phase time and measure the hydrogen production efficiency and kinetics. Hydrogen production in a stirred batch reactor was performed for 150–200 h, at given operating conditions using a previously defined growth media, to validate the model. Using the proposed model, the cumulated moles of produced hydrogen correlate well with those predicted from the pH curve. Hence, the modified Gompertz model parameters, largely used for describing the hydrogen generation kinetics by dark fermentation, were estimated from the pH curve and from the experimentally measured generated hydrogen. Satisfactory agreement was found, thus, validating the method.