Giovanni Maria Grasso

Prof. Giovanni Maria Grasso

orcid

Research Focus & Metrics

Academic Career Length

32Years (1995-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 February 2013 in Superconductor Science and Technology
Verified
Journal Article
Open access
JPJ Pelegrín
J Pelegrín
GRGiuseppe Romano
Giuseppe Romano
EMELENA MARTÍNEZ
ELENA MARTÍNEZ
LALuis A. Angurel
Luis A. Angurel
RNR Navarro
R Navarro
DND Nardelli
D Nardelli

1 October 1995 in Superconductor Science and Technology
Verified
Journal Article
Closed access
PDF file
YLY H Li
Y H Li
JKJ A Kilner
J A Kilner
MDM Dhalle
M Dhalle
ACA D Caplin
A D Caplin
Giovanni Maria GrassoGiovanni Maria Grasso
Giovanni Maria Grasso
RFR Flukiger
R Flukiger
TEM studies of a Bi-2223 tape have shown that amorphous layers from about 10 nm to more than 100 nm in width were present at c-axis twist boundaries in the highly textured Bi-2223 tape which showed a limited residual weak-link field dependence at low fields ( mu 0H<0.1 T) followed by a slow exponential decay at higher fields. This kind of amorphous layer is likely to be insulating, and this strongly suggests that Jc is not limited by c-axis current transport as proposed by the 'brick wall' model. The most frequently observed low-angle grain boundaries are ab-axis grain boundaries containing no (001) planes. A modified 'rail switch' model was proposed with low-angle ab-axis grain boundaries at the switches rather than low-angle c-axis grain boundaries as suggested by Hensel et al.

1 October 2006 in Advances in Science and Technology
Verified
Conference Paper
Closed access
PDF file
AMA. Malagoli
A. Malagoli
Giovanni Maria GrassoGiovanni Maria Grasso
Giovanni Maria Grasso
MVMaurizio Vignolo
Maurizio Vignolo
ATAndrea Tumino
Andrea Tumino
VBV. Braccini
V. Braccini
MMMarco Modica
Marco Modica
In spite of the relatively short time dedicated to the development of MgB2 conductors since its discovery in 2001, a remarkable progress has been already achieved in terms of critical current density, homogeneity of the conductors and reproducibility of the results over long lengths. Unlike other HTS and LTS materials, MgB2 conductor processing is more open to a number of improvements and modifications that help in making it more attractive for several DC and AC applications. Up to now our work has been focused on the improvement of the production capacity in order to allow for the assembly of large prototype magnets to test the capability of MgB2 to maintain the present level of performance over very long lengths. Long MgB2 tapes of about 1600 m with superconducting and mechanical properties suitable for making low field magnets are already available. Presently we are focusing on the enhancement of the irreversibility field. This would open the possibility of using MgB2 also for high field applications.

22 November 2024 in ACTA IMEKO
Verified
Journal Article
Open access
PDF file
FSFabio Lo Savio
Fabio Lo Savio
Giovanni Maria GrassoGiovanni Maria Grasso
Giovanni Maria Grasso
GMGiuseppe Maccarrone
Giuseppe Maccarrone
Nowadays the coastal waters of the Mediterranean Sea are increasingly affected by pollution from aromatic hydrocarbons. Therefore, in order to implement damage minimization actions, a continuous monitoring system with rapid response is needed. The most effective local method for distinguishing aromatic hydrocarbons from salt water is UV-induced fluorescence. This paper describes the design and building of a UV-induced fluorescence sensor that, mounted on board a sensor-buoy, detects the presence or absence of the pollutant in any atmospheric condition. The sensor consists of a measuring chamber, in which the water, loaded by a submersible pump, maintains a constant level thanks to a small siphon. The detection system, consisting of a UVC-LED and a phototransistor that responds in the visible light band, is located in the upper part of the chamber. In vitro tests, performed by comparing the sensor results with those obtained from a spectrofluorometer, have shown good sensitivity, repeatability, and accuracy, despite the inexpensiveness and low energy consumption of the sensor. An important goal achieved by the design and building methodology is that the sensor is able to withstand harsh weather conditions, the corrosive action of salt water and biofouling.

1 December 2019 in Polymer Testing
Verified
Journal Article
Closed access
FSF. Lo Savio
F. Lo Savio
MBMarco Bonfanti
Marco Bonfanti
Giovanni Maria GrassoGiovanni Maria Grasso
Giovanni Maria Grasso
Damiano AlizzioDamiano Alizzio
Damiano Alizzio

Verified
Journal Article
Open access
PDF file
Giovanni Maria GrassoGiovanni Maria Grasso
Giovanni Maria Grasso
LOLudovica Maria Oliveri
Ludovica Maria Oliveri
FCFerdinando Chiacchio
Ferdinando Chiacchio
The growing demand for floating offshore structures calls for lightweight, impact-resilient, and sustainable design approaches. This study explores the optimization of composite fibree layup in a 30 m hull subjected to slamming-type hydrodynamic loads. Although based on a recreational vessel, the model serves as a transferable case for offshore applications such as wave energy devices, offshore wind platforms, and floating PV systems. A finite element method (FEM) model was developed using shell elements and a sinusoidal time-dependent pressure to simulate slamming events on the wet surface of the hull. The response was evaluated under different fiber orientation schemes, aiming to reduce structural mass while maintaining stress levels within safety margins. Results showed that strategic layup optimization led to a measurable reduction in total material usage, without compromising structural integrity. These outcomes suggest multiple advantages, including an approximately 14% reduction in raw material demand, which in turn facilitates for potential downsizing of propulsion systems and transportation energy due to lighter structures. Such improvements contribute indirectly to reduced emissions and operational costs. The methodology presented offers a replicable approach to composite optimization under transient marine loads, with relevance for sustainable offshore structural design.