Girum Mindaye Mengistu

Mr. Girum Mindaye Mengistu

Department of Construction Materials, Budapest University of Technology and Economics, Budapest, Hungary
orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 January 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
GMGirum Mindaye Mengistu
Girum Mindaye Mengistu
RNRita Nemes
Rita Nemes
As the use of 3D-printed concrete becomes more prevalent, the need for effective recycling methods becomes paramount. This study addresses this concern by exploring the repurposing of 3D-printed concrete waste as an aggregate in normal-strength concrete for C30/37 and C40/50 classes, covering both fine and coarse aggregates in its particle size distribution. The extent of recycled aggregate (RA) replacement was determined through sieve analysis. A two-stage investigation assessed the compressive strength performance of the concrete specimens. The initial stage produced reference specimens with no replacement, representing conventional concrete. In the second stage, variable specimens incorporated 50% and 67% recycled aggregate (RA) from 3D-printed concrete waste. Results revealed that in C40/50, both the 50% and 67% replacements consistently exhibited a higher strength than 0%. In C30/37, the 50% replacement displayed decreased strength compared to the 0% and 67%, while the 67% replacement consistently showed superior strength. Adjusting the water content impacted strength; at 67%, slight variations occurred, while at 50%, extra water led to a significant decrease. An overarching discovery is that the efficacy of the 67% replacement level holds regardless of the concrete strength class.

16 February 2023 in Solids
Verified
Journal Article
Open access
PDF file
GMGirum Mindaye Mengistu
Girum Mindaye Mengistu
ZGZoltán Gyurkó
Zoltán Gyurkó
RNRita Nemes
Rita Nemes
This paper presents the study of a two-hundred-year-old, demolded solid clay brick using the rebound hammer test for the estimation of the compressive strength. During the test, the location and face type influence on the rebound values are monitored and recorded. In addition, the calculation of the average rebound value has been modified to encounter the influence of location and face types. Furthermore, the estimated compressive strength is compared with the normalized mean compressive strength to check the accuracy of the rebound hammer test if it is within the confidential limit of ±25%. The result shows that the location and surface types have influence on the rebound value, which in turn affected the compressive strength.

6 June 2025 in Results in Engineering
Verified
Journal Article
Open access
GMGirum Mindaye Mengistu
Girum Mindaye Mengistu
RNRita Nemes
Rita Nemes

17 February 2025 in Heliyon
Verified
Journal Article
Open access
GMGirum Mindaye Mengistu
Girum Mindaye Mengistu
RNRita Nemes
Rita Nemes
This study investigates the strength of recycled aggregate concrete (RAC) incorporating 3D-printed concrete (3DPC) waste as recycled aggregates over a year. With the growing adoption of 3DPC, recycling its waste presents a sustainable solution to mitigate environmental impact and conserve resources. The 3DPC waste was processed into recycled aggregates through a single stage crushing method using a jaw crusher, producing a mix of fine and coarse aggregates. These recycled aggregates were blended with the river sand at 50 %, and 67 % of the total aggregate content to produce C30/37 and C40/50 strength classes. The experimental program involved performing a rebound hammer test, a nondestructive testing (NDT) method, to estimate compressive strength while considering the effects of replacement ratio, aggregate type, specimen age, and surface temperature. The results were then validated with a standard compression test, a destructive testing (DT) method, to evaluate the reliability of the NDT approach. Findings reveal that density significantly influences RAC compressive strength, with strength increasing progressively over time. Surface temperatures above 30 °C moderately reduced estimated compressive strength, causing deviations of up to 11.5 %. RAC mixes with 50 % and 67 % recycled aggregates exhibited higher compressive strength, except for the C30-RA50 mix, which deviated from this trend. An empirical formula was developed using rebound hammer and standard compression results to predict RAC strength and was compared with existing curve equations. These findings provide a robust basis for improving NDT-based strength assessments of RAC and highlight the potential of utilizing 3DPC waste in sustainable construction practices.

11 March 2026 in Heliyon
Verified
Journal Article
Open access
GMGirum Mindaye Mengistu
Girum Mindaye Mengistu
MTMilán Máté Tóth
Milán Máté Tóth
RNRita Nemes
Rita Nemes