Hadi Y. Kanaan

Prof. Dr. Hadi Y. Kanaan

orcid

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 March 2010 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
CFCharles J. Fallaha
Charles J. Fallaha
MSMaarouf Saad
Maarouf Saad
Hadi Y. KanaanHadi Y. Kanaan
Hadi Y. Kanaan
KAKamal Al-Haddad
Kamal Al-Haddad
In this paper, sliding-mode control is applied on multi-input/multi-output (MIMO) nonlinear systems. A novel approach is proposed, which allows chattering reduction on control input while keeping high tracking performance of the controller in steady-state regime. This approach consists of designing a nonlinear reaching law by using an exponential function that dynamically adapts to the variations of the controlled system. Experimental study was focused on a MIMO modular robot arm. Experimental results are presented to show the effectiveness of the proposed approach, regarding particularly the chattering reduction on control input in steady-state regime.

21 October 2013 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
BKBachir Kedjar
Bachir Kedjar
Hadi Y. KanaanHadi Y. Kanaan
Hadi Y. Kanaan
KAKamal Al-Haddad
Kamal Al-Haddad
The aim of this paper is to introduce power quality added function to the standard Vienna rectifier in order to compensate reactive power and to cancel current-type harmonics drawn by nonlinear loads connected to the same point of common coupling. A theoretical investigation that demonstrates the ability of such topology to compensate harmonics and limited reactive power is first presented. Then, the design and implementation of a linear quadratic regulator with integral action is presented. The converter is controlled as a whole i.e., a multiple-input-multiple-output system, and uses an augmented model that was developed in the d- q frame. Experimental results obtained with a digital-signal-processor-based DS1103 controller and the converter operating at a 20-kHz switching frequency proved the effectiveness of the theoretical study and the high performance of the proposed control strategy in compensating load harmonics and limited reactive power.

11 March 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
MBMohammad Babaie
Mohammad Babaie
MSMohammad Sharifzadeh
Mohammad Sharifzadeh
Hadi Y. KanaanHadi Y. Kanaan
Hadi Y. Kanaan
Kamal Al-HaddadKamal Al-Haddad
Kamal Al-Haddad
Seven-level Packed U-Cell (PUC7) is known as a cost-effective, low-component multilevel inverter. However, PUC7 challenge is the capacitor voltage balancing; so, it conventionally needs an additional voltage control integrated into the current control loop. Because of extra variables, control problem is further complicated for grid-connected PUC7. This paper proposes an Optimized Sliding Mode Control (OSMC) based on the current dynamical model to track the load current reference and to self-balance the capacitor voltage in both grid-connected and stand-alone operations. By optimizing the OSMC control factor using a Visual Based Optimization (VBO) method, PUC7 switching operation is controlled to self-balance the capacitor voltage while any extra voltage controller is needed. An adaptive control law has been also proposed for self-tuning of the PUC7 current reference to track the load and DC source variations. Experimental and simulation results of PUC7 prove the excellent performance of the proposed OSMC in achieving capacitor self-voltage balancing operation.

25 June 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
FSFadia Sebaaly
Fadia Sebaaly
MSMohammad Sharifzadeh
Mohammad Sharifzadeh
Hadi Y. KanaanHadi Y. Kanaan
Hadi Y. Kanaan
Kamal Al-HaddadKamal Al-Haddad
Kamal Al-Haddad
This paper proposes a Modified Finite-Set Model Predictive Control (M-FS-MPC) for multilevel switching mode operation of grid-connected nine-level Packed E-Cell (PEC9) inverter. With single-DC source, six power switches, back-to-back connected switches as bidirectional and two capacitors horizontally extended, PEC9 inverter topology has remarkably reduced components count. PEC prominent feature is the capability to switch among different multilevel voltage; nine- seven- or five- level under faulty switch case without any structure modification and only if the controller is appropriately designed. M-FS-MPC is proposed to operate grid-connected PEC with multilevel switching mode under bidirectional switch fault operation. Switching among five- seven- or nine-level voltages is attained by proper DC capacitors voltages regulation whereas the desired current injection with low THD and requested power factor for addressing grid connectivity applications is guaranteed. System discrete model is developed and experimental results verify the performance and robustness of M-FS-MPC in targeting the capability of PEC multilevel switching mode operation and grid connectivity requirements in both steady and transient states.

1 November 2015
Verified
Conference Paper
Closed access
HVHani Vahedi
Hani Vahedi
Hadi Y. KanaanHadi Y. Kanaan
Hadi Y. Kanaan
KAKamal Al-Haddad
Kamal Al-Haddad
Packed U-Cell (PUC) converter has been introduced as a 7-level converter in early 2008. Since then, different analysis and projects have been performed on, including various applications such as inverter and rectifier, linear and nonlinear voltage controllers. In this paper, authors try to do a detail review on this topology covering all aspects like topology design in single and three-phase, operation concepts, switching sequences for different multilevel voltage waveform generation, modelling and etc. It is shown that this topology can be comparable to popular multilevel converters (CHB and NPC) in terms of device counts and applications. Moreover, some performed and published works about the PUC are mentioned to show its different industrial applications and some other converter topologies derived based on the PUC. Experimental results are provided to show the good performance of PUC converter in several applications.

19 December 2013 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
Hadi Y. KanaanHadi Y. Kanaan
Hadi Y. Kanaan
MCMaxime Caron
Maxime Caron
KAKamal Al-Haddad
Kamal Al-Haddad
The need to reduce the time consumption in developing and implementing power converters, and to improve the effectiveness of the test equipment, continues to grow. This trend is further accelerated through the development of electricity-based technology, such as the electric or hybrid vehicle. As the price of energy continues to increase, regenerative test equipment used for validating power converters are gaining importance and attention. This paper focuses on the development of a two-stage regenerative power load emulator. This type of intelligent load requires a connection to the network interface, which, for some applications, should be bidirectional and must possess a galvanic isolation. The development of such grid-connected unit that processes ac-dc conversion is treated in this paper. A 5 kW prototype is used as a base to model, simulate, design, implement, and test such a system. The stability of the interconnection between the two conversion stages is established and tested in real-time applications. The prototype was tested at 180, 220, and 260 V RMS. The measured efficiency is higher than 90%, and the power factor is 0.99 over a wide range of operation.