In advanced sensor system designs, one of the common methods involves converting target physical quantities into phase/frequency-modulated signals. Then, the in-phase/quadrature-phase (I/Q)-based phase demodulation structure is mainly employed to enhance flexibility and efficiency in obtaining the phase information. However, the presence of I/Q imbalance and additive noise in analog I/Q channels greatly degrade the overall system detection performance. Specifically, we investigated the detailed degradation of signal detection, including the introduction of unwanted interference frequency components, elevated noise floor, and distortion of the target signal. To solve this problem, we proposed a novel controlled-carrier closed-loop structure to realize the phase demodulation. This structure, built upon the zero-error closed-loop structure, further mitigates the imbalance distortion and optimizes the noise performance by modifying the control method. The detailed structure and key issues are provided. Further, the effectiveness and enhanced performance of the proposed structure are verified by simulation and experiments. The experimental results align with the simulations and it shows that the proposed structure can achieve enhanced imbalance-distortion mitigation and noise suppression without the need for complex I/Q estimation and compensation.
Frequency-modulated (FM) signals are widely used in sensing, measurement, and signal detection due to their strong anti-interference and easy transmission characteristics. Although the high-precision measurement methods for static signals are quite complete, the high-precision measurement methods for dynamic FM signals still need to be studied, and the measurement accuracy in the high-sampling system still has room for improvement. Traditionally, the equal-precision measurement method is widely applied in most scenarios. However, its accuracy is limited by the quantization error of ±1 word and the sampling gate time, making it difficult to improve the frequency measurement accuracy while ensuring a high sampling rate at the same time. In this paper, a high-precision feedback frequency measurement system with the capability to eliminate the quantization error of ±1 word is proposed. The proposed system consists of two stages, the rough measurement stage based on the equal-precision measurement method and the precise measurement stage based on the negative feedback tracking architecture using the phase–frequency detector (PFD) and direct digital synthesizer (DDS). The effectiveness and feasibility of the system are verified by both simulation and experiment. At the sampling rate of 2 kHz, the frequency measurement accuracy is improved by more than 30 dB.
3 October 2024 in IEEE Photonics Technology Letters
Noise floor is an important metric for fiber optic sensors. In particular, common-mode noise (CMN) suppression is critical to improving the system’s ability to detect weak signals. In this paper, an innovative method for reducing noise in white-light-driven sensors is proposed. This structure fully utilizes the broad spectrum of white light and the wavelength selectivity of fiber gratings. The proposed CMN suppression method is capable of suppressing the phase noise of the light source, as well as the noise due to environmental disturbances. The experiments demonstrate that the noise floor of this vibration sensor is about -88 dB/Hz above 30Hz with 10km disturbed transmission fiber. The max 1/f noise reduction can reach approximately 60 dB near 5 Hz, while the max transmission path noise suppression exceeds 103 dB at hundreds of Hz. The proposed structure has the potential to achieve higher resolution in wavelength division multiplexing (WDM) sensor arrays without excessive cost.
The clock source is the most fundamental part of the microwave-based sensing system. Its phase noise and jitter performance directly determine the detecting accuracy of the entire system. Therefore, there are many applications that require a high-performance low-jitter clock source integrated on a single board together with other functional circuits. However, with the increased integration level of single-board circuits, the frequency of the onboard signal, and the requirements for miniaturization, the influence of power supply noise on the clock source generation module cannot be ignored. In other words, the power supply induced jitter (PSIJ) will arise inevitably to some extent. In addition, reducing the PSIJ has become increasingly difficult by optimizing the power supply network. This paper analyzes the output clock jitter of the phase-locked loop (PLL) based clock source under the influence of power supply noise and proposes a reasonable optimization design of the loop filter bandwidth to further suppress the impact of the power supply noise (PSN). The simulation results show that using the optimized loop filter, the output clock jitter can be attenuated by 78% in the case that the output has been influenced by the wideband noise and the bump power supply noise.
Substrate integrated waveguides (SIW) have been widely used in the design of high-performance narrowband filters and the integration of microwave circuits in recent years, owing to their high quality factor and easy planarization. In the design of single-board integration, in order to achieve high quality factor and narrow-band SIW filter, a low-cost and effective method is to increase the thickness of the substrate layer within a certain range to achieve lower insertion losses. However, with the switching of the reference ground planes, a discontinuous return path will be induced. Improper handling of the structure will give rise to additional losses and radiation which will lead to EMC issues. In this paper, a method is proposed to extend the inner ground at the discontinuous section to form a stepped transition structure to achieve good signal transmission performance. The simulation results show that at 10GHz, the center frequency of SIW in our design, the proposed transition structure has 1.8dB lower insertion loss as well as 40.14dB higher return loss than the structure of direct interconnection at the discontinuous section.
Large dynamic range (DR) is one of the primary requirements in fiber-optic acoustic sensing systems, wherein acoustic signals are converted into phase-modulated (PM) signals for detection. In the signal transduction stage, research has been conducted to increase the phase sensitivity. This allows for the conversion of acoustic signals into PM signals with higher phase modulation indices (PMIs), therefore improving the detection of weak acoustic signals. However, higher PMIs induced by strong acoustic signals correspondingly broaden the signal bandwidth. A phase demodulation structure that provides both high-bandwidth capability and low-noise performance is needed to improve both the upper and lower limits of DR. To solve the contradiction between phase demodulation noise and bandwidth, we proposed a novel phase demodulation structure featuring an enhanced phase acquisition method and an enhanced feedback control algorithm. The enhanced phase acquisition method combines high-precision analog-to-digital converter (ADC) sampling data with high-frequency comparator data, enhancing the capability to capture dynamic phase variations. The enhanced feedback control algorithm incorporates a predictive control method using high-order signal models and Kalman Filter (KF) iteration to optimize phase tracking performance. With the proposed demodulation structure, phase variation in the residual signal is reduced and the residual signal bandwidth is compressed before sampling. This combined approach effectively balances noise and bandwidth. The performance of the proposed structure is validated through simulations and experiments, achieving a DR of 170.1 dB@1 kHz with a phase resolution of 4×10 -6 rad/ √ Hz in practical tests. Based on our estimation, the optimal DR is approximately 211.5 dB@1 kHz.