The study of the damage process of rock under external loads is good guidance for geotechnical construction design. The differences in rock damage processes and damage modes under different stress paths are rarely reported. To explore the effects of stress paths on rock damage processes, uniaxial compression experiments under three stress paths were conducted. Numerical simulation is also used to simulate the rock acoustic emission (AE) and fracture process. The results of the study indicate that the maximum acoustic emission events are at the peak of stress, and fractures are mainly formed at this stage. The peak of AE energy occurs before the peak of AE events. The damage pattern and fragmentation size of the rock are related to the way the stresses are loaded. It is noticed that there is appearance of a quiet period of AE events prior to the production of significant cracks. Minor damage to the rock is accompanied by the generation of bright white spots in the specimen, which is due to the high tensile or shear stress in the units. When the stress in these units exceeds their strength, the units break down and tiny cracks appear. As the external load increased, the cracks developed and penetrated, and the specimen was damaged. Under cyclic loading and unloading, the number of AE events increased significantly compared with the controlled displacement and controlled stress loading methods, and the radius of the AE circle became larger and the energy also increased, which indicates a greater degree of destruction of the rock under cyclic loading and unloading. The results of the study are of reference significance for rock crack propagation and fracture mode influenced by stress conditions and provide some guidance for construction design under different working conditions.

Investigating the micro-parameters of rock is vital for understanding the macro-properties of rock, such as the uniaxial compressive strength (UCS), Young’s modulus, failure patterns, etc. In this paper, based on the experimental results of rock material, a parallel-bond model in three-dimensional particle flow code (PFC3D) was applied to investigate the effects of the joint action of bond stiffness ratio and bond stress ratio on macro-properties of rock. The uniaxial compressive strength, stress–strain relationships, and failure characteristics, as well as underlying compression and failure mechanisms, in the process of parameter calibration, were systematically studied. The results indicated that the interaction of several micro-parameters would obviously change the response characteristics of the macro-properties of the model. The mechanism of the effects of various micro-parameters on the macro-properties of the model was further revealed. The change of the micro-parameters would change the strength and stress state of the bond between particles. The research results could promote the understanding of the failure mechanism of rock and improve the efficiency of micro-parameter calibration and the accuracy of calibration results.

Mudstone, whose significant characteristic is water-weakening, widely exists in all kinds of geotechnical engineering, which brings great security risks to engineering safety. In this paper, through a series of macro and meso test methods, the macro and meso action mechanism of water on the weakly consolidated plane of mudstone was studied. In the uniaxial compressive strength test, the mudstone cementation plane was the main part of the fracture derived. Under the moist state, the strength of mudstone would decrease significantly, which was inversely correlated with relative moisture content. In the case of flooding, mudstone cracking occurred only along the cementation plane. Through ESEM+mapping test, results showed the humidification curing caused obvious damage to the cemented plane, where sodium and calcium were lost without a certain cause. The cemented plane was rich in kinds of clay minerals in mesoscale and presented an inhomogeneous state. The surface hardness data obtained from nanoindentation were discrete and difficult to quantitatively evaluate the mesomechanical properties. However, compared with the dry state, the data set of the moist state had a significant decline, showing a weakening effect. The mudstone is prone to fail along these weakly consolidated planes. Moisture intrudes into the bedding plane further deteriorating their consolidation.

To reveal the influence of ultra-close coal seams mining on surrounding rock disturbance, PFC^2D is introduced to establish a simplified particle flow model of strata in the deeply buried mine, the damage and stress evolution characteristics of the surrounding rock were studied based on double coal seam mining. The results show that after the model excavation, the fracture length of the rock strata reached an accuracy of 97% compared with the theoretical calculation results, showing a good match with the theoretical calculations and the initial stress level obtained by the subsequent model monitoring is consistent with the measured value. The primary and secondary key layers are broken as a result of mining the higher coal seam, the siltstone interlayer is unaffected while the bottom coal seam is partially harmed, and there is noticeable extrusion damage between the rocks. Meanwhile, the damage to the rocks inside the gob is only becoming worse as a result of mining the lower coal seam. While the surrounding rock of the upper coal seam mining exhibits clear stress redistribution features in three zones, the lower coal seam mining creates a local and multi-point high-stress distribution. The siltstone interlayer’s stress variation is essentially identical to that of the surrounding rock. The extrusion state among rocks is related to the porosity of the shattered surrounding rock area. The siltstone interlayer is pressured during the upper coal seam mining, but it maintains its integrity, only collapsing during the lower coal seam mining. Though the siltstone interlayer can retain the necessary integrity of support before the lower coal seam mining, its internal stress is unstable which should be paid attention to when designing the support scheme during the mining period.

The micromechanism of the effects of different height/width ratios (H/W) and initial stress levels on unloading characteristics of deep rock was investigated based on PFC3D true-triaxial unloading simulation. The results show that the increase of H/W will increase the movement speed of rock particles and intensify the acoustic emission (AE) activity inside the rock. With the increase of H/W, the failure mode of rock changes from splitting failure to tensile-shear failure. With increasing initial stress level, the particle velocity and overall fragmentation degree of rock increase. However, the increase of lateral stress will limit the coalescence of microfractures and weaken AE activity in the rock. Under unloading condition, the bonds between particles generally crack along the unloading direction, and the tensile effect is more pronounced under the condition of low initial stress level and high H/W. Under unloading condition, the variable energy of rock increases with increasing H/W and initial stress level, and the kinetic energy of rock particles increases with increasing H/W. The increase of initial stress level will increase the kinetic energy of rock particles when H/W is high.