Muhammad Imran

Dr. Muhammad Imran

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 August 2018 in ACS Nano
Verified
Journal Article
Closed access
DHDengbao Han
Dengbao Han
Muhammad ImranMuhammad Imran
Muhammad Imran
MZMengjiao Zhang
Mengjiao Zhang
SCShuai Chang
Shuai Chang
XWXian-Gang Wu
Xian-Gang Wu
HZHaizheng Zhong
Haizheng Zhong

21 February 2022 in Crystals
Verified
Journal Article
Open access
PDF file
KKKAFFAYATULLAH KHAN
KAFFAYATULLAH KHAN
MAMuhammad Amin
Muhammad Amin
Muhammad UsmanMuhammad Usman
Muhammad Usman
Muhammad ImranMuhammad Imran
Muhammad Imran
MAMajdi AlFaiad
Majdi AlFaiad
FSFaisal I. Shalabi
Faisal I. Shalabi
The aim of this study was to investigate the influence of fineness and heat-treatment on the pozzolanic and engineering properties of volcanic ash. To this end, two different fineness levels of volcanic ash, ultra-fine (VAF) and fine (VA), without and after heat treatment at different temperatures (VA550, VA650, and VA750), were partially substituted for cement. In addition to the control (100% cement), five binary mortar mixes, each containing 20% of the different types of volcanic ash (VAF and VA; heat-treated and not), were prepared. First, X-ray fluorescence (XRF), X-ray powder diffraction (XRD), particle size analysis, and modified Chappelle tests were used to characterize the material. All mortar mixes were then tested for compressive strength development, water absorption, and apparent porosity. Finally, the microstructure of each of the mixes was evaluated by performing XRD, thermogravimetric analysis (TGA), and Fourier transform infrared spectroscopy (FTIR) analyses on paste samples at 91 days post-formation. The XRD and Chappelle reactivity results revealed increased pozzolanic reactivity with increasing volcanic ash fineness. In contrast, heat treatment adversely affected the pozzolanic reactivity of the volcanic ash due to the formation of crystalline phases at high temperatures. The mortars containing VAF20 (VAF, no heat, at 20%) showed slightly improved compressive strength (69.6 MPa) than the control (68.1 MPa) and all other binary mixes (66.7, 63.5, 64.2, and 63.9 MPa for VA20, VA20-550, VA20-650, and VA20-750, respectively) at 91 days. The mortar containing VAF20 demonstrated the lowest level of water absorption (9.3%) and apparent porosity (19.1%) of all mixes, including the control. The XRD results for the paste samples show that both VA and VAF showed the least intensity of portlandite phase, as compared to the control and other binary mixes. TGA results also show that binary mixes of VA and VAF have a reduced amount of portlandite, resulting in the densification of the mixes’ microstructures. With the addition of VAF, there is a significant shift in the FTIR band from 980 to 992 cm−1, which causes the formation of additional C–S–H gels that lead to the densification of the paste matrix. These results demonstrate that VAF exhibits high pozzolanic reactivity, making it suitable for use as a natural pozzolan that can partially substitute cement in the production of strong, durable, and environmentally friendly concrete.

20 October 2022 in Materials
Verified
Journal Article
Open access
PDF file
HAHassan Ali Alkadhim
Hassan Ali Alkadhim
MAMuhammad Amin
Muhammad Amin
WAWaqas Ahmad
Waqas Ahmad
KKKAFFAYATULLAH KHAN
KAFFAYATULLAH KHAN
SNSohaib Nazar
Sohaib Nazar
Muhammad ImranMuhammad Imran
Muhammad Imran
This research employed machine learning (ML) and SHapley Additive ExPlanations (SHAP) methods to assess the strength and impact of raw ingredients of cement mortar (CM) incorporated with waste glass powder (WGP). The data required for this study were generated using an experimental approach. Two ML methods were employed, i.e., gradient boosting and random forest, for compressive strength (CS) and flexural strength (FS) estimation. The performance of ML approaches was evaluated by comparing the coefficient of determination (R2), statistical checks, k-fold assessment, and analyzing the variation between experimental and estimated strength. The results of the ML-based modeling approaches revealed that the gradient boosting model had a good degree of precision, but the random forest model predicted the strength of the WGP-based CM with a greater degree of precision for CS and FS prediction. The SHAP analysis revealed that fine aggregate was a critical raw material, with a stronger negative link to the strength of the material, whereas WGP and cement had a greater positive effect on the strength of CM. Utilizing such approaches will benefit the building sector by supporting the progress of rapid and inexpensive approaches for identifying material attributes and the impact of raw ingredients.

28 July 2019 in Advanced Optical Materials
Verified
Journal Article
Closed access
PDF file
XZXin Zhang
Xin Zhang
DHDengbao Han
Dengbao Han
CWChenhui Wang
Chenhui Wang
Muhammad ImranMuhammad Imran
Muhammad Imran
FZFeng Zhang
Feng Zhang
HZHaizheng Zhong
Haizheng Zhong

2 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
Mohammed Najeeb Al-HashemMohammed Najeeb Al-Hashem
Mohammed Najeeb Al-Hashem
MAMuhammad Amin
Muhammad Amin
MRMuhammad Raheel
Muhammad Raheel
KKKAFFAYATULLAH KHAN
KAFFAYATULLAH KHAN
HAHassan Ali Alkadhim
Hassan Ali Alkadhim
MIMudassir Iqbal
Mudassir Iqbal
Climate change has become trending news due to its serious impacts on Earth. Initiatives are being taken to lessen the impact of climate change and mitigate it. Among the different initiatives, researchers are aiming to find suitable alternatives for cement. This study is a humble effort to effectively utilize industrial- and agricultural-waste-based pozzolanic materials in concrete to make it economical and environmentally friendly. For this purpose, a ternary blend of binders (i.e., cement, fly ash, and rice husk ash) was employed in concrete. Different variables such as the quantity of different binders, fine and coarse aggregates, water, superplasticizer, and the age of the samples were considered to study their influence on the compressive strength of the ternary blended concrete using gene expression programming (GEP) and artificial neural networking (ANN). The performance of these two models was evaluated using R2, RMSE, and a comparison of regression slopes. It was observed that the GEP model with 100 chromosomes, a head size of 10, and five genes resulted in an optimum GEP model, as apparent from its high R2 value of 0.80 and 0.70 in the TR and TS phase, respectively. However, the ANN model performed better than the GEP model, as evident from its higher R2 value of 0.94 and 0.88 in the TR and TS phase, respectively. Similarly, lower values of RMSE and MAE were observed for the ANN model in comparison to the GEP model. The regression slope analysis revealed that the predicted values obtained from the ANN model were in good agreement with the experimental values, as shown by its higher R2 value (0.89) compared with that of the GEP model (R2 = 0.80). Subsequently, parametric analysis of the ANN model revealed that the addition of pozzolanic materials enhanced the compressive strength of the ternary blended concrete samples. Additionally, we observed that the compressive strength of the ternary blended concrete samples increased rapidly within the first 28 days of casting.

8 January 2019 in Physica Status Solidi (RRL) – Rapid Research Letters
Verified
Journal Article
Closed access
PDF file
SAShmshad Ali
Shmshad Ali
SCShuai Chang
Shuai Chang
Muhammad ImranMuhammad Imran
Muhammad Imran
QSQingfan Shi
Qingfan Shi
YCYu Chen
Yu Chen
HZHaizheng Zhong
Haizheng Zhong