The search for fossil fuels substitutes forces the use of new propulsion technologies applied to means of transportation. Already widespread, hybrid vehicles are beginning to share the market with hydrogen-powered propulsion systems. These systems are fuel cells or internal combustion engines powered by hydrogen fuel. In this context, road tests of a hydrogen fuel cell drive were conducted under typical traffic conditions according to the requirements of the RDE test. As a result of the carried-out work, energy flow conditions were presented for three driving phases (urban, rural and motorway). The different contributions to the vehicle propulsion of the hydrogen system and the electric system in each phase of the driving route are indicated. The characteristic interaction of power train components during varying driving conditions was presented. A wide variation in the contribution of the fuel cell and the battery to the vehicle’s propulsion was identified. In urban conditions, the share of the fuel cell in the vehicle’s propulsion is more than three times that contributed by the battery, suburban—7 times, highway—28 times. In the entire test, the ratio of FC/BATT use was more than seven, while the energy consumption was more than 22 kWh/100 km. The amounts of battery energy used and recovered were found to be very close to each other under RDE test conditions.
31 March 2020 in Eksploatacja i Niezawodność – Maintenance and Reliability
The assessment of energy flow through electric vehicle systems makes estimating their energy consumption possible. The article presents analyzes of the energy consumption of electric vehicles in selected driving tests (NEDC, WLTC and in real traffic conditions – RDC test) in relation to the vehicles different curb weight. The use of electric motors was also analyzed, providing their operating ranges, data of the energy flow in batteries and the change in their charge level. Simulation tests and analyzes were carried out using the AVL Cruise software. It was found that despite similar vehicle energy consumption values in NEDC and RDC testing, there are significant differences in energy flow in vehicle subsystems. The changes in the battery charge level per 100 km of test drive are similar in both the WLTC and RDC tests (6% difference); for the NEDC test, this difference is the greatest at 25% (compared to the previous tests). The energy consumption of electric vehicles depends significantly on the test itself; the values obtained in the tests are in the ranges of 10.1–13.5 kWh/100 km (NEDC test); 13–15 kWh/100 km (WLTC test) and 12.5–16.2 kWh/100 km in the RDC test. The energy consumption values in the NEDC and WLTC tests, compared to the RDC test, are approximately 20% and 10% lower, respectively. Increasing the vehicle mass increases the energy consumption (increasing the vehicle mass by 100 kg was found to increase the energy consumption by 0.34 kWh/100 km).
Hybrid vehicles allow an increase in the powertrain efficiency thanks to their design. One such factor is the use of increased voltage supplying electric motors to the voltage supplying the high voltage battery. The battery voltage is increased several times in the inverter (boost) system to increase the final electric power supplied to the electric motor. The article presents the possibilities of using such a voltage boost in urban and non-urban driving conditions. The tests were performed on the latest generations of parallel hybrid drive systems in Lexus NX 300h and Toyota RAV4 hybrid vehicles. It has been shown that the boost system is used in about 30–40% of the urban drive distance (up to 20% of the driving time). The power supply voltage boost of the electric motors of both vehicles is used throughout the entire engine speed range of these machines at high torque values. Research has shown that the maximum voltage gain – approximately three times (up to 650 V) – is within the maximum torque range of the electric motors and allows for doubling the torque generated by the drive.
Fuel cells are one of the zero-emission elements of modern automotive drive systems. This article presents theoretical identification of the component parameters of indicators for the fuel cell operating conditions. Activation, ohmic, and mass transport losses were identified. Current–voltage characteristics were provided along with an analysis of typical cell losses. The actual performance characteristics of fuel cells were analyzed for Toyota Mirai I and II generation vehicles. The fuel cells operating conditions were derived and analyzed in the context of real driving conditions. Therefore, urban, rural, and motorway conditions were used. The vehicles were equipped with PEM fuel cells supplying power equal to 114 kW (1st gen.) or 128 kW (2nd gen.). The average fuel cell stack power values depend on the driving conditions: urban (about 10 kW), rural (20 kW) and motorway (about 30–40 kW) driving modes. The different power ratings of fuel cells combined with different battery generations resulted in a variation in the cells operating conditions. Analyses conducted in various traffic conditions indicated the possibility of determining losses related to the fuel cells. The analysis of fuel cell losses shows the greatest values for activation losses when the cells are under high load (for both generations)—i.e., in motorway driving conditions. The voltage of resistive losses reached its maximum in urban driving conditions when the load on the fuel cells was small.