Показано, что в последние годы в отечественной и мировой практике широкое применение нашли самоуплотняющиеся бетонные смеси отличающиеся высокой удобоукладываемостью без применения вибрационного воздействия. С применением инновационных технологий могут быть изготовлены разнообразные материалы и изделия архитектурно-строительного назначения с улучшенными декоративными свойствами. Приведены результаты исследования по подбору составов декоративно-отделочных порошково-активированных бетонов зернистой фактурой поверхности по реологическим свойствам, показателям прочности и морозостойкости. При проведении исследований в качестве вяжущего использовался египетский белый цемент, микронаполнителя – микрокварц, тонкодисперсного компонента – отсевы дробления гранита и купершлака фр. 0–0,63 мм, песка-заполнителя – гранитные высевки фр. 0,63–5 мм и купершлак фр. 0,63–2,5 мм. Смеси пластифицировались суперпластификаторами нового поколения отечественного и зарубежного производства. Рассчитаны структурные и реотехнологические показатели порошково-активированных бетонов. Из полученных значений условных реологических критериев порошково-активированных бетонов следует, что все они значительно больше единицы и характеризуют существенное превышение объемов реологических матриц над объемами тонкозернистых, грубозернистых компонентов, которые вмещаются в них с большими раздвижками частиц и зерен. Прочность как комплексная механическая характеристика, включающая сочетание критериев прочности, надежности и долговечности, является важнейшим параметром качества структуры бетона как активного и самого массового строительного материала конструкционного назначения. Здания и сооружения в условиях эксплуатации подвергаются циклическим механическим нагрузкам различного вида и климатическим воздействиям, характеризующимся циклическими проявлениями отрицательных и знакопеременных температур. В результате выполнения исследований выявлены высокие показатели прочности и морозостойкости декоративных порошково-активированных бетонов с зернистой фактурой поверхности.
Porous glass-ceramic materials are used in the construction engineering and repair of various objects. The article investigates the method for obtaining porous glass ceramics from siliceous rock with a high calcite content. To obtain samples with an even fine porous structure, a small amount (≤0.386%) of chloride (NaCl, KCl, MgCl2·6H2O, CaCl2) was added to the charge mixture. At the first stage, mechanochemical activation of raw materials was carried out. Siliceous rock, Na2CO3 and additives (chlorides) were grinded together in a planetary ball mill. The resulting charge was annealed at a temperature of 850 °C. The influence of the type and amount of chloride on the properties of the charge mixture and glass ceramics has been defined by thermal analysis (TA), X-ray diffraction (XRD), scanning electron microscopy (SEM), etc. The chlorides in the charge mixture decreased the calcite’s decarbonization temperature and had an effect on the macro- and microstructure of the material. As a result, samples of glass ceramics with an even finely porous structure in the form of blocks were obtained. The samples consist of quartz, wollastonite, devitrite, anorthoclase and an amorphous phase. On average, 89–90% of the resulting material consists of with small pores. The apparent density of the samples is in the range of 245–267 kg/m3. Bending and compressive strength reaches 1.75 MPa and 3.8 MPa, respectively. The minimum thermal conductivity of the modified samples is 0.065 W/(m∙°C). The limiting operating temperature is 860 °C, and the minimum thermal shock resistance is 170 °C. The material has a high chemical stability. They can be used as thermal insulation for some types of industrial and civil facilities.
31 December 2024 in Nanotechnologies in Construction: A Scientific Internet-Journal
It is common knowledge that microorganisms cause biological damage to structures and facilities within various buildings and constructions. One of the most effective ways to increase the biological resistance of construction and industrial materials is the introduction of biocides into their composition. This article presents the results of research on the inactivation of various types of microorganisms with new disinfectants of the Teflex group derived from polyhexamethylguanidine hydrochloride. In the course of research, it was revealed that the specimens have biocidal (bactericidal), fungicidal and sporicidal activity when tested on bacterial suspensions and contaminated surfaces.
The purpose of the research described in this article was to optimize the compositions based on hydraulic-modified binder and construction waste for waterproofing and repair of concrete or brick structures in contact with the ground, as well as the study of properties and development of the basis of the methodology for selecting the composition of such a waterproofing system. Processing of the results of the experiment was carried out by statistical and analytical methods. The research was based on a method for determining the adhesive strength of a waterproofing coating, based on the determination when the insulating layers are torn off. As a result of the calculation and experimental verification, the composition of the waterproofing material was obtained, which corresponds to an adhesive strength of 3.8 MPa; the strength of the waterproofing layer was 36–37 MPa, as well as the amounts of the main components: acrylic resin 3.9%; finely ground concrete waste 80 kg/m3; plasticizer consumption (0.38…0.39%) at the optimum moisture content of the base surface (9.7…9.8%).