The inspection of corrosion under insulation (CUI) has been identified as a significant challenge in the petroleum and chemical process industries. As some of the most effective strategies, pulsed eddy current (PEC) techniques have proved effective for the measurement of the CUI of pipelines. In this paper, we propose a circular-arc array (CAA) to improve the measurement efficiency for the PEC inspection of thermally insulated pipelines. Based on the PEC system model for inspecting the CUI of pipelines, the magnetic field distribution of the CAA with multiple excitors was investigated. It is shown that the coverage of induced magnetic field gets much larger than that of the single excitor to realize high-efficiency measurements. Moreover, a sparsely distributed receiver array is designed to further improve the signal-to-noise ratio by eliminating the waviness effect due to multiple excitors. Finally, experiments were conducted, and the results demonstrated the effectiveness of the proposed method for the inspection of thermally insulated pipelines.

In this article, we address the problem of synthesized magnetic field focusing (SMF) of the pulsed eddy-current (PEC) technology for the non-destructive testing (NDT) of oil and gas well casing pipes. The electromagnetic response excited by multiple transmitters was derived using the signal model of downhole PEC system. The magnetic field was shown to be adjustable by modifying the currents of the multiple transmitting array. Based on this property, magnetic fields were synthesized with the mean squared error (MMSE) criterion to be focused on the center of the transmitting array, and a weighted MMSE (WMMSE)-based SMF was also proposed to achieve an optimal synthetic magnetic field. Furthermore, the primal-dual interior-point method was used to solve the WMMSE optimization problem with the total and single transmit power constraints for the practical application. Simulations and experimental results showed that the SMF with the PEC array effectively focuses the eddy-current field on the center of the transmitting array.

In this article, we present a space–time pulsed eddy current (PEC) array for nondestructive testing (NDT) of wellbore casings using a multiple-input multiple-output (MIMO) technique. On the basis of a multilayered cylindrical wellbore model, an MIMO-PEC model is developed according to the phase shift characteristics of the PEC response corresponding to different transmitting–receiving (TR) distances. To achieve a more significant number of TR channels than in a traditional receiving array to reduce the complexity of the TR structure, a space–time transmission scheme is proposed to recover multiple TR channels. Moreover, a specific space–time MIMO array structure is designed to maximize the number of independent TR channels. The effectiveness of the proposed method is verified by applying the proposed MIMO array to a borehole PEC system for NDT of wellbore casings. The simulation and experimental results demonstrate that using the array structure and space–time transmission scheme proposed in this article, an MIMO structure consisting of ${M}$ transmitters and ${N}$ receivers can be equivalent to a transceiver system with a single transmitter and ${M}\,\,\times \,\,{N}$ receivers. Thus, MIMO technique can be effectively applied to PEC-NDT systems and drastically reduce the cost and complexity of the PEC system.

Pulsed eddy current (PEC) is a widely utilized technology for the nondestructive inspection of industrial tubes and pipes due to its rapid and accurate results. To improve the longitudinal resolution of PEC, multiple transmitting coils (MTCs) are used to realize magnetic focusing. However, this approach is difficult to apply to narrow downhole environments because of the complex transmitting array and electrical circuits. To address this issue, we present a synthesized transmitting coil (STC) that combines MTCs into a single coil with multiple connected sections using different winding directions and number of turns to adjust the magnetic field distribution. A theoretical derivation was presented for the analysis and interpretation of the magnetic field, and a figure of merit (FoM) was constructed to optimize the STC parameters. Numerical simulations and experiments were performed to validate the proposed STC for downhole casing inspection, and the experimental results showed good agreement with the simulation results.

Crosswell electromagnetic (EM) methods are widely used in subsurface geophysical prospecting because they can achieve more effective long-distance detection than single-well methods. However, a large-diameter borehole is required to increase the magnetic moment of the magnetic dipole source. For the long-distance detection of copper ores, which is usually performed in slim holes, we present a borehole-surface current-injection-based crosswell EM logging method. Considering the cost of deploying casing, we inject a low-frequency AC directly into the ground, and converging current is formed around low-resistance anomalies in the formation. Then, the distribution of the anomalies can be inferred by detecting the low-frequency alternating magnetic field of the converging current in the receiver well. Moreover, to further improve the detection performance, we design a placement scheme for the grounding electrode for multi-anomaly crosswell detection based on the Gauss–Newton inversion algorithm, where the EM responses for different grounding electrode locations are analyzed. Field experiments are conducted using two slim open holes spaced approximately 1000 m apart for the detection of two copper ores. Through the processing and interpretation of measured EM signals, the conductivity imaging results of the crosswell EM method indicate that the measured distribution of anomalies is consistent with prior knowledge obtained from numerous single-well loggings, demonstrating the feasibility of the proposed application for long-distance crosswell EM logging in slim open holes.