Biocompatible polymer films demonstrating excellent thermal stability are highly desirable for high-temperature (>250 °C) applications, especially in the bioelectronic encapsulation domain. Parylene, as an organic thin film, is a well-established polymer material exhibiting excellent barrier properties and is often the material of choice for biomedical applications. This work investigated the thermal impact on the bulk properties of four types of parylene films: parylene N, C, VT4, and AF4. The films, deposited using the standard Gorham process, were analyzed at varying annealing temperatures from room temperature up to 450 °C. Thermal properties were identified by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) methods, while X-ray diffraction (XRD) analysis showed the effect of high-temperature exposure on the structural properties. In addition to thermal and structural analysis, the barrier properties were measured through the helium transmission rate (HTR) and the water vapor transmission rate (WVTR). Fluorinated parylene films were confirmed to be exceptional materials for high-temperature applications. Parylene AF4 film, 25um thick, demonstrated excellent barrier performance after 300 °C exposure, with an HTR and a WVTR of 12.18 × 103 cm3 (STP) m−2 day−1 atm−1 and 6.6 g m−2 day−1, respectively.
The integration of nonlinear current-voltage selectors and bi-stable memristors is a paramount step for reliable operation of crossbar arrays. In this paper, the self-aligned assembly of a single nanometer-scale device that contains both a selector and a memristor is presented. The two components (i.e., selector and memristor) are vertically assembled via a self-aligned fabrication process combined with electroforming. In designing the device, niobium oxide and tantalum oxide are chosen as materials for selector and memristor, respectively. The formation of niobium oxide is visualized by exploiting the self-limiting reaction between niobium and tantalum oxide; crystalline niobium (di)oxide forms at the interface between metallic niobium and tantalum oxide via electrothermal heating, resulting in a niobium oxide selector self-aligned to a tantalum oxide memristor. A steady-state finite element analysis is used to assess the electrothermal heating expected to occur in the device. Current-voltage measurements and structural/chemical analyses conducted for the virgin device, the electroforming process, and the functional selector-memristor device are presented. The demonstration of a self-aligned, monolithically integrated selector-memristor device would pave a practical pathway to various circuits based on memristors attainable at manufacturing scales.
1 January 2021 in Solar Energy Materials and Solar Cells
Thermal runaway is a major safety concern in the applications of Li-ion batteries, especially in the electric vehicle (EV) market. A key component to mitigate this risk is the separator membrane, a porous polymer film that prevents physical contact between the electrodes. Traditional polyolefin-based separators display significant thermal shrinkage (TS) above 100 °C, which increases the risk of battery failure; hence, suppressing the TS up to 180 °C is critical to enhancing the cell's safety. In this article, we deposited thin-film coatings (less than 10 nm) of aluminum oxide by atomic layer deposition (ALD) on three different types of separator membranes. The deposition conditions and the plasma pretreatment were optimized to decrease the number of ALD cycles necessary to suppress TS without hindering the battery performance for all of the studied separators. A dependency on the separator composition and porosity was found. After 100 ALD cycles, the thermal shrinkage of a 15 μm thick polyethylene membrane with 50% porosity was measured to be below 1% at 180 °C, with ionic conductivity >1 mS/cm. Full battery cycling with NMC532 cathodes demonstrates no hindrance to the battery's rate capability or the capacity retention rate compared to that of bare membranes during the first 100 cycles. These results display the potential of separators functionalized by ALD to enhance battery safety and improve battery performance without increasing the separator thickness and hence preserving excellent volumetric energy.
23 September 2019 in IEEE Journal of Photovoltaics
In this article, we investigate the contact resistivity of p-type passivating contacts for silicon solar cells. Our contact structures are compatible with firing, a rapid annealing process similar to the one used for sintering of the screen-printed metallization in solar cell manufacturing. We find that the short firing process crystallizes the doped layers and incorporates active boron dopants up to the solubility concentration at the chosen firing temperature. The dependence of our contact resistivities on carrier density and temperature suggest that the hole transport is a combination of tunneling through the oxide at the wafer surface and of thermionic field emission over the Schottky barrier to the metallization. For ideal firing conditions, we find implied open-circuit voltages up to 720 mV and contact resistivities as low as 15 m·Ω·cm2.