Jakub Poloprudský

Mr. Jakub Poloprudský

Institute of Physics of Materials, Academy of Sciences of Czech Republic, Brno, Czech Republic
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 September 2021 in Materials
Verified
Journal Article
Open access
PDF file
JPJakub Poloprudský
Jakub Poloprudský
ACAlice Chlupová
Alice Chlupová
IŠIvo Šulák
Ivo Šulák
TKTomáš Kruml
Tomáš Kruml
Sergej HlochSergej Hloch
Sergej Hloch
This article deals with the effect of periodically acting liquid droplets on the polished surfaces of AISI 316L stainless steel and Ti6Al4V titanium alloy. These materials were exposed to a pulsating water jet produced using an ultrasonic sonotrode with an oscillation frequency of 21 kHz placed in a pressure chamber. The only variable in the experiments was the time for which the materials were exposed to water droplets, i.e., the number of impingements; the other parameters were kept constant. We chose a low number of impingements to study the incubation stages of the deformation caused by the pulsating water jet. The surfaces of the specimens were studied using (1) confocal microscopy for characterizing the surface profile induced by the water jet, (2) scanning electron microscopy for detailed surface observation, and (3) transmission electron microscopy for detecting the changes in the near-surface microstructure. The surface described by the height of the primary profile of the surface increased with the number of impingements, and was substantially more intense in the austenitic steel than in the Ti alloy. Irregular surface depressions, slip lines, and short cracks were observed in the Ti alloy, whereas pronounced straight slip bands formed in the austenitic steel. The dislocation density near the surface was measured quantitatively, reaching high values of the order of 1014 m−2 in the austenitic steel and even higher values (up to 3 × 1015 m−2) in the Ti alloy. The origins of the mentioned surface features differed in the two materials: an intense dislocation slip on parallel slip planes for the Ti alloy and mechanical twinning combined with dislocation slip for the austenitic steel.

30 July 2024 in Archives of Civil and Mechanical Engineering
Verified
Journal Article
Open access
PDF file
Gabriel StolárikGabriel Stolárik
Gabriel Stolárik
DKDagmar Klichová
Dagmar Klichová
JPJakub Poloprudský
Jakub Poloprudský
ACAlice Chlupová
Alice Chlupová
Akash NagAkash Nag
Akash Nag
Sergej HlochSergej Hloch
Sergej Hloch
Submerged jets have a variety of practical applications due to their versatility in providing efficient and environmentally friendly options for treatment in various industries. The physical background is based on the continuous water jet (CWJ) application powered via stagnation pressure. However, it is known that impact pressure is much more effective than static pressure. When the impact pressure is repeated with a high frequency per time unit, the erosive effects of water can be used even at pressures below 100 MPa, which is attractive from the point of view of the low demands of the hydraulic system. Surface modification utilising impact pressure can be achieved by employing the pulsed water jet (PWJ) method. The combination of parameters such as the traverse speed and trajectory pattern can control the number of water clusters impacting the material surface. So far, the field of application of PWJ for surface treatment has mostly been investigated water atmospheric conditions. This article focuses on the possibility of the surface modification of AISI 304L stainless steel using the PWJ method under submerged conditions. The results are compared to those obtained under atmospheric conditions. The reference samples were treated by the same technological conditions using a continuous water jet (CWJ). The affected surfaces were characterised using areal surface roughness parameters Sa, Sz, Sp, and Sv, and the surface topography and mechanism of erosion wear were evaluated by scanning electron microscopy. A significant increase in all roughness parameters was confirmed using the PWJ compared to the CWJ method (both in atmospheric and submerged conditions), which confirms the importance of using impact pressure. The surface treatment by PWJ under submerged conditions resulted in a decrease of the surface roughness parameter Sa by approximately 97% compared to atmospheric conditions at a traverse speed of 2 mm/s for perpendicular interleaved trajectory, nevertheless, the homogeneity of treatment over a larger area was improved.

24 December 2024 in Materials Science and Engineering: A
Verified
Journal Article
Open access
TBT. Babinský
T. Babinský
IŠIvo Šulák
Ivo Šulák
MGMarkéta Gálíková
Markéta Gálíková
IKI. Kubĕna
I. Kubĕna
JPJakub Poloprudský
Jakub Poloprudský
LNL. Náhlík
L. Náhlík

1 November 2023 in Engineering Science and Technology, an International Journal
Verified
Journal Article
Open access
GSGabriel Stolárik
Gabriel Stolárik
DKDagmar Klichová
Dagmar Klichová
JPJakub Poloprudský
Jakub Poloprudský
Akash NagAkash Nag
Akash Nag
SHSergej Hloch
Sergej Hloch

7 February 2025 in Wear
Verified
Journal Article
Closed access
DKDagmar Klichová
Dagmar Klichová
Gabriel StolárikGabriel Stolárik
Gabriel Stolárik
ANAkash Nag
Akash Nag
JPJakub Poloprudský
Jakub Poloprudský
ACAlice Chlupová
Alice Chlupová
SHSergej Hloch
Sergej Hloch

18 February 2025 in Wear
Verified
Journal Article
Closed access
ACAlice Chlupová
Alice Chlupová
JPJakub Poloprudský
Jakub Poloprudský
ANAkash Nag
Akash Nag
DKDagmar Klichová
Dagmar Klichová
KSKamil Souček
Kamil Souček
Sergej HlochSergej Hloch
Sergej Hloch