Jaroslav Cihlář, Jr.

Dr. Jaroslav Cihlář, Jr.

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 October 2025 in Recycling
Verified
Journal Article
Open access
PDF file
PSPavel Straka
Pavel Straka
OBOlga Bičáková
Olga Bičáková
JJJaroslav Cihlář, Jr.
Jaroslav Cihlář, Jr.
Crosslinked polyethylene (XLPE) is a widely used material which—unlike polyethylene—is very stable both chemically and mechanically. Therefore, waste from this material is difficult to process. A very promising way is slow pyrolysis catalyzed by FeTiO3 (ilmenite), which allows the conversion of this waste into hydrocarbons via degradation of the rigid chemical structure of crosslinked material. High liquid hydrocarbon yields were achieved by slow pyrolysis both without and with a catalyst at a final temperature of 470 °C (65 and 75–76 wt.%, respectively), but with the catalyst significantly changing the composition of the resulting hydrocarbons. To reveal the possibilities of using the FeTiO3 catalyst for processing waste XLPE, the effect of this catalyst on the degradation of the XLPE structure was investigated. The degradation is probably greatly facilitated by the action of the FeTiO3 catalyst at the defect sites of the XLPE structure, i.e., at the tertiary carbons in the main chain where branching into cross-links occurs. In this way, the FeTiO3 catalyst, even in very small amounts (1%), significantly promotes the degradation of the XLPE structure. This leads to the formation of liquid hydrocarbons, up to 92 wt.% of the products obtained. The novelty of this work lies in a technologically feasible method for processing resistant crosslinked waste material using an inexpensive catalyst; the proposed method provides hydrocarbons with high utility value. On the whole, slow pyrolysis of XLPE waste catalyzed by FeTiO3 at a final temperature of 470 °C and carried out under well-defined conditions appears to be a promising method for converting this waste into valuable hydrocarbons and energy gas.

1 November 2025 in Catalysts
Verified
Journal Article
Open access
PDF file
PSPavel Straka
Pavel Straka
JJJaroslav Cihlář, Jr.
Jaroslav Cihlář, Jr.
OBOlga Bičáková
Olga Bičáková
The aim of this work is to present a technologically feasible method for processing biomass into synthesis gas or hydrogen-rich gas. Three types of biomass with different lignin contents were pyrolyzed in a pyrolysis unit under well-defined conditions (ambient pressure, heating rate of 10 K min−1, end temperature of 500 °C, operating particle size, variable catalyst mass) in the presence of a ruthenium catalyst (Ru/Al2O3, powder), and the effect of catalyst amount on the yield and gas composition was observed. Feedstock mass was always 50 g, and catalyst mass was 2.5, 5, and 10 g (mixing ratios 0.05, 0.1, and 0.2, resp.). During pyrolysis, the raw gas and vapors was passed through the catalyst bed and converted to the resulting gas and bio-oil. The gas obtained was cleaned by sequestration with CO2 using commercial active carbon to obtain syngas with different H2/CO ratios or hydrogen-rich gas. It was found that, depending on the catalyst amount, slow pyrolysis catalyzed by ruthenium yielded syngas with a H2/CO ratio of approximately 0.5–5, which is further usable. The by-products obtained (bio-oil and biochar) are also described. Bio-oils from all three biomass types contained mainly carboxylic acids (33–46 wt.%) and phenols (18–33 wt.%), hydroquinone (up to 5 wt.%), and a high amount of stearate (up to 26 wt.%). All of these compounds have high utility value. The resulting biochar can probably be applied, after activation using CO2, as a sorbent. In conclusion, under energy-efficient conditions (end temperature max. 500 °C), Ru/Al2O3-catalyzed pyrolysis of biomass provides syngas or hydrogen-rich gas and usable by-products. It should be emphasized that the maximum theoretical H2 production from biomass is 60–70 g H2/kg biomass. This limit value could negatively affect the technological development of the process.

11 May 2024 in Gels
Verified
Journal Article
Open access
PDF file
JCJaroslav Cihlář
Jaroslav Cihlář
STSerhii Tkachenko
Serhii Tkachenko
VBVendula Bednaříková
Vendula Bednaříková
JJJaroslav Cihlář, Jr.
Jaroslav Cihlář, Jr.
KČKlára Částková
Klára Částková
LČLadislav Čelko
Ladislav Čelko
Dense multi-cationic Sm-Co-O, Sm-Ni-O, Al-Co-O, Al-Ni-O, and Al-Ni-Co-O oxide aerogels were prepared by epoxide-driven sol–gel synthesis. Catalysts for dry reformation of methane, Sm2O3/Co, Sm2O3/Ni, Al2O3/Co, Al2O3/Ni, Al2O3/Co, and Ni were prepared by reduction of aerogels with hydrogen and their catalytic activities and C-deposition during dry reformation of methane were tested. Catalytic tests showed high methane conversion (93–98%) and C-deposition (0.01–4.35 mg C/gcat.h). The highest content of C-deposits after catalytic tests was determined for Al2O3/Co and Al2O3/Ni catalysts, which was related to the formation of Al alloys with Co and Ni. A uniform distribution of Co0 and Ni0 nanoparticles (in the form of a CoNi alloy) was found only for the Al2O3/Co and Ni catalysts, which showed the highest activity as well as low C deposition.

28 May 2025 in Processes
Verified
Journal Article
Open access
PDF file
PSPavel Straka
Pavel Straka
JJJaroslav Cihlář, Jr.
Jaroslav Cihlář, Jr.
The purpose of this work is to present a technologically feasible method for processing different types of biomass into energy-rich gas with a methane content higher than 60 vol.% or a hydrogen content higher than 65 vol.%. Selected biomass samples with different compositions were tested. Samples with an operational particle size were pyrolyzed under well-defined conditions in a sealed pressure reactor, and the influence of process parameters on the gas yield and composition was evaluated. Different metal catalysts were used. It was found that, depending on the catalyst used, slow catalyzed pressure pyrolysis at a final temperature of 400 °C yields a methane-rich gas with up to 70 vol.% CH4 or a hydrogen-rich gas with up to 75 vol.% H2. In addition, by-products (oil and biochar) were analyzed and their uses described. In conclusion, under energy-saving conditions, pressure-catalyzed pyrolysis of biomass provides energy-rich gas and other usable products.

20 July 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
PSPavel Straka
Pavel Straka
JJJaroslav Cihlář, Jr.
Jaroslav Cihlář, Jr.
OBOlga Bičáková
Olga Bičáková
The aim of the work is to present a technologically feasible method for processing waste biomass into synthesis gas for further use, namely for the synthesis of bio-methanol, which is considered an important renewable fuel. Walnut shells were tested as lignocellulosic waste. Samples with an operating particle size (0.5–3 mm) were pyrolyzed under well-defined conditions in a sealed pressure reactor, using chromium (III) oxide particles and fine particles as a catalyst. The effect of particle size on the yield and composition of resulting synthesis gas and biochar was tested. It was found that slow, catalyzed pressure pyrolysis at a final temperature of 400 °C provides synthesis gas with a H2/CO ratio of up to 0.9 or up to 1.8 and biochar (35–39 wt.%) useful as biofuel. These products were analyzed and their use described. The residual product was greywater (25–35 wt.%). Overall, under energy-saving conditions (slow pyrolysis, final temperature of 400 °C), pressure and catalyzed pyrolysis of biomass provide usable products and acceptable residuum.

31 March 2026 in Paliva
Verified
Journal Article
Closed access
PSPavel Straka
Pavel Straka
OBOlga Bičáková
Olga Bičáková
JJJaroslav Cihlář, Jr.
Jaroslav Cihlář, Jr.
Waste crosslinked polyethylene (XLPE) can be a source of valuable hydrocarbons for further use. XLPE is widely used material which – unlike polyethylene – is very stable both chemically and mechanically. There-fore, its waste is difficult to process. A very promising way is slow pyrolysis catalyzed by ruthenium (Ru/Al2O3) which allows the conversion of waste into hydrocarbons via degradation of rigid chemical structure of cross-linked material. High hydrocarbon yields (91–92 wt.%) were achieved by slow pyrolysis without or with cata-lyst, but significant changes in the composition of resulting gas and oil were found with the Ru/Al₂O₃ catalyst. To reveal the possibilities of using this catalyst for processing of XLPE at a relatively lower final temperature (max. 480 °C, mostly 450–470 °C), an effect of the catalyst on degradation of XLPE structure and related rheological properties of XLPE melt was investigated. It was found that the activation energy of degradation decreases significantly in the presence of the catalyst and the degradation is greatly facilitated by Ru/Al2O3 at the defect sites of the XLPE structure (the tertiary carbons). By the catalyst, the torque for XLPE melt and the its shear viscosity are significantly reduced already at 250 °C. Thus, Ru/Al2O3 catalyst, even in very small amounts (1 wt.% Ru), significantly promotes the degradation of XLPE structure and reduces the solid pyrolysis residue. This finding greatly facilitates the processing of waste XLPE. The catalytic mechanism of action of Ru is outlined and the equations for the XLPE cleavage are given. The main product of processing, pyrolysis oil, can be used as a clean heating fuel, or oil for further use, or a source of solvents, liquid and solid hydrocarbons, especially paraffin.