Extreme ultraviolet lithography (EUVL) is a leading-edge technology for pattern miniaturization and the production of advanced electronic devices. One of the current critical challenges for further scaling down the technology is reducing the line-edge roughness (LER) of the final patterns while simultaneously maintaining high resolution and sensitivity. As the target sizes of features and LER become closer to the polymer size, polymer chain conformations and their distribution should be considered to understand the primary sources of LER. Here, we proposed a new approach of EUV photoresist modeling with an explicit description of polymer chains using a coarse-grained model. Our new simulation model demonstrated that interface variation represented by width and fluctuation at the edge of the pattern could be caused by characteristic changes of the resist material during the lithography processes. We determined the effect of polymer chain conformation on LER formation and how it finally contributed to LER formation with various resist material parameters (e.g., Flory–Huggins parameter, molecular weight, protected site ratio, and Tg).
1 April 2022 in Journal of Micro/Nanopatterning, Materials, and Metrology
Background: The chemically amplified resist (CAR) has been the workhorse of lithography for the past few decades. During the evolution of projection lithography to extreme ultraviolet lithography (EUVL), a continuous reduction in feature size is observed. Also, a reduction in resist film thickness (FT) is required to prevent large aspect ratios that lead to pattern collapse. A further reduction in resist FT, into an ultrathin film regime (<30 nm resist FT), is expected when advancing to high NA EUVL. This brings along associated challenges with (1) resist critical dimension scanning electron microscope (CDSEM) metrology and (2) resist patterning performance. Aim: Assessment of metrology challenges and patterning limits of a CAR working in this ultrathin film regime. Deconvoluting the metrology and patterning effect on the determination of the unbiased line width roughness (uLWR). Approach: Patterning a CAR at different nominal resist FTs on two different underlayers to quantify the changes in CDSEM image quality and resist patterning performance with the resulting uLWR changes. Results: The CDSEM image signal-to-noise ratio (SNR) depends on resist FT and the underlayer. The uLWR increases with a reduction in resist FT but scales differently on the two underlayers. Conclusions: A relationship between CDSEM image SNR and uLWR is found. The SNR and uLWR scaling difference on the two underlayers, as well as the uLWR dependency on SNR was determined to be a metrology effect. The general uLWR increase for a reduced resist FT was determined to be a patterning effect.
Extreme ultra-violet lithography (EUVL) is the leading-edge technology to produce advanced nanoelectronics. The further development of EUVL is heavily based on implementing the so-called high numerical aperture (NA) EUVL, which will enable even smaller pitches up to 8 nm half pitch (HP). In anticipation of this high NA technology, it is crucial to assess the readiness of the current resist materials for the high NA regime to comply with the demanding requirements of resolution, line-edge roughness, and sensitivity (RLS). The achievable tighter pitches require lower film thicknesses for both resist and underlying transfer layers. A concern that is tied to the thinning down is the potential change in resist properties and behavior due to the interaction with the underlayer. To increase the fundamental understanding of ultra-thin films for high NA EUVL, a method to investigate the interplay of reduced film thickness and different patterning-relevant underlayers is developed by looking at the glass transition temperature (Tg) of polymer-based resists. To minimize the ambiguity of the results due to resist additives (i.e., photoacid generator (PAG) and quencher), it was opted to move forward with polymer-only samples, the main component of the resist, at this stage of the investigation. By using dielectric response spectroscopy, the results obtained show that changing the protection group of the polymer, as well as altering the polymer film thickness impacts the dynamics of the polymer mobility, which can be assessed through the Tg of the system. Unexpectedly, changing the underlayer did not result in a clear change in the polymer mobility at the tested film thicknesses.
MOx resists have matured into promising alternatives to conventional CAR resists for advanced-node EUV lithography where these materials offer potential improvements to patterning fidelity and high etch resistance based on metallic components. This is a particular boon for processes with limited exposure latitudes such as High-NA EUV lithography. Creating and employing first-principle models of MOx lithographic processes should speed adoption and development of these materials and represents an important aspect of platform maturation. Stochastic photochemical models of metalcontaining resist systems have previously been developed, but without extension to computational lithography. Likewise, stochastic models derived from CAR systems have been fit to MOx lithographic data using computational lithography software, facilitating limited stochastic lithography studies without capturing fundamental MOx imaging processes. Recently, a rigorous stochastic model built from the ground up using MOx-specific resist principles has been developed. In this contribution, the performance of this MOx-specific model was assessed by comparing simulated and experimental lithography data for a series of MOx resists under a range of exposure and process conditions. Chemical and physical properties of the resists derived independently from X-ray diffraction, EUV absorbance, FTIR spectroscopy, and ellipsometry measurements were parameterized in the context of the simulation, and calibration routines were used to fit simulated data to experimental CD-SEM exposure data produced using an NXE-3300B EUV scanner. Insights from these models may be used to guide MOx resist development and EUV lithography process optimization. Ultimately, these studies will help to identify process windows, processing points, and possibly improvements to the MOx resists.
As feature sizes continue to shrink, low-k1 lithographic processes are required to advance chip technologies. In this context, both advances in optical systems and imaging capabilities as well as improvements in EUV photoresist have led to practical gains in resolution. This work focusses on our latest attempt to characterize photoresist performance by a metric that can effectively exclude all other contributors (e.g. scanner) and quantify the true photoresist capabilities. By a cautious analysis of the previous k4 metric for several use cases and resist platforms (chemically amplified vs. metal-oxide resist), we propose an improved formula that incorporates key resist attributes.
1 April 2021 in Journal of Micro/Nanopatterning, Materials, and Metrology
The Journal of Micro/Nanopatterning, Materials, and Metrology (JM3) publishes peer-reviewed papers on the core enabling technologies that address the patterning needs of the electronics industry.