The Radiation and Dust Sensor is one of six sensors of the Mars Environmental Dynamics Analyzer onboard the Perseverance rover from the Mars 2020 NASA mission. Its primary goal is to characterize the airbone dust in the Mars atmosphere, inferring its concentration, shape and optical properties. Thanks to its geometry, the sensor will be capable of studying dust-lifting processes with a high temporal resolution and high spatial coverage. Thanks to its multiwavelength design, it will characterize the solar spectrum from Mars’ surface. The present work describes the sensor design from the scientific and technical requirements, the qualification processes to demonstrate its endurance on Mars’ surface, the calibration activities to demonstrate its performance, and its validation campaign in a representative Mars analog. As a result of this process, we obtained a very compact sensor, fully digital, with a mass below 1 kg and exceptional power consumption and data budget features.
23 January 2023 in Journal of Geophysical Research: Planets
The Mars Environmental Dynamics Analyzer, onboard the Perseverance rover, is a meteorological station that is operating on Mars and includes, among other sensors, the radiometer Radiation and Dust Sensor (RDS). From RDS irradiance observations, a total of 374 dust devils (DDs) were detected for the first 365 sols of the mission (Ls = 6°–182°), which along with wind and pressure measurements, we estimated a DD frequency of formation at Jezero between 1.3 and 3.4 DD km −2 sol −1 (increasing as we move from spring into summer). This frequency is found to be smaller than that estimated at the Spirit or Pathfinder landing sites but much greater than that derived at InSight landing site. The maximum in DD frequency occurs between 12:00 and 13:00 local true solar time, which is when the convective heat flux and lower planetary boundary layer IR heating are both predicted to peak in Jezero crater. DD diameter, minimum height, and trajectory were studied showing (a) an average diameter of 29 m (or a median of 25 m) and a maximum and minimum diameter of 132 ± 63.4 and 5.6 ± 5.5 m; (b) an average minimum DD height of 231 m and a maximum minimum‐height of 872 m; and (c) the DD migration direction is in agreement with wind measurements. For all the cases, DDs decreased the UV irradiance, while at visible or near‐IR wavelengths both increases and decreases were observed. Contrary to the frequency of formation, these results indicate similar DD characteristics in average for the studied period.
The ExoMars programme, which is carried out by European Space Agency (ESA) in cooperation with the Russian federal Space Agency (Roscosmos), foresees a two-steps mission to Mars. The first mission consists of an orbiter and an Entry Descent and Landing Demonstrator Module (EDM) to be launched in January 2016 and is scheduled to land on the planet during the statistical dust storm season; the second mission includes a descent module, a surface platform and a rover and will be launched in 2018. The DREAMS (Dust characterization, Risk assessment and Environment Analyser on the Martian Surface) experiment for ExoMars 2016 is an autonomous meteorological station designed to study the effect of dust on Martian environment which will operate for two Martian days (sols) relying on its own power supply after landing. DREAMS includes a suite of sensors able to analyse temperature, pressure, humidity, wind speed and direction and solar irradiance as well as an electric field probe which will perform the first electrical characterization of Mars surface atmosphere.
Components off the shelf (cots) photodiodes suitable for OWLS were irradiated with ~10 to ~60 MeV protons and up to fluences of ~2.5-10 12 p/cm 2 . Electrical and optoelectronic parameters were measured during the test (I-V curves, dark current, responsivity and ideal diode factor). Results on degradation and post-annealing are reported. Preliminary results on the lattice effects are also pointed.
1 September 2005 in 2005 8th European Conference on Radiation and Its Effects on Components and Systems
LEDs and photodiodes (PDs) suitable for OWLS were irradiated with 52 MeV protons and up to 2.8ldr1012 p/cm2 (in 5 steps). Electrical and optoelectronics parameters have been characterized during the test (characteristic I-V curve, dark current, PD responsivity and LED optical power) results about degradation and are reported. Also, the differences in degradation rate for several biasing conditions during irradiation have been studied.