Polystyrene (PS), a thermoplastic polymer, is used in many applications due to its mechanical performance, good chemical inertness, and excellent processability. However, it is doped with different nanomaterials for reasons such as improving its electrical conductivity and mechanical properties. In this study, carbon nanotube (CNT)-added PS composites were produced with the aim of combining the properties of CNTs, such as their low weight and high tensile strength and Young’s modulus, with the versatility, processability, and mechanical properties of PS. In this study, multi-walled carbon nanotube (MWCNT)-reinforced polystyrene (PS) composites with different percentage ratios (0.1, 0.2, and 0.3 wt%) were prepared by a plastic injection molding method. The mechanical, microstructural, and thermal properties of the fabricated PS/MWCNT composites were characterized by Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FTIR) Spectroscopy, Atomic Force Microscopy (AFM) and Thermogravimetric Analysis (TGA) techniques. AFM analyses were carried out to investigate the surface properties of MWCNT-reinforced composite materials by evaluating the root mean square (RMS) values. These analyses show that the RMS value for MWCNT-reinforced composite materials decreases as the weight percentage of MWCNTs increases. The TGA results show that there is no change in the degradation temperature of the 0.1%- and 0.2%-doped MWCNT composites compared to pure polystyrene, but the degradation of the 0.3%-doped MWCNT composite is almost complete at a temperature of 539 °C. Among the PS/MWCNT composites, the 0.3%-doped MWCNT composite exhibits more thermal stability than pure PS and other composites. Similarly, the values of the percentage elongation and tensile strength of 0.3% MWCNT-doped composites was obtained as 1.91% and 12.174% mm2, respectively. These values are higher than the values of 0.1% and 0.2% MWCNT-doped composite materials. In conclusion, the mechanical and thermal properties of MWCNT-reinforced PS polymers provide promising results for researchers working in this field.
31 March 2020 in Bilge International Journal of Science and Technology Research
Günümüzde nanopartikül takviyeli kompozitlerin endüstriyel kullanımı giderek artmaktadır. Kullanılan nanopartikül takviyeleri ile kompozitin birçok özellliğinde iyileşme sağlanabilmiştir ve bu durum onları birçok alanda tercih sebebi yapmaktadır. Nanopartiküllerle üretilen kompozit malzemeler diğer yöntemlerle üretilen malzemelere göre daha fonksiyonel ve üstün özelliklere sahiptir. Kompozitlerin kullanıldığı alanlardan biri de yalıtım malzemeleridir. Eklenen farklı takviyelerle bu malzemelerin özellikleri geliştirilmektedir. Bu çalışmada polistiren matris içerisine farklı ağırlık oranlarında 30 µm parçacık boyutlu grafen takviyesi ile kompozit üretilmiştir. Saf polistirene ağırlıkça %0,1, 0,2 ve 0,3 oranlarında nano takviyeler eklenmiş ve plastik enjeksiyon yöntemiyle malzemeler üretilmiştir. Malzemelerin üretim aşamasında kristal polistirenler eritilip nano takviyelerle birleştirilip kalıplara dökülerek üretilmiştir. Birleştirme esnasında malzemelerin homojen dağılımı için 80 Rpm hızında 10 dakika boyunca karıştırılmıştır. Üretilen kompozit malzemelere mikroyapı karakterizasyonu için SEM analizi, mekanik ve ısıl özelliklerin belirlenmesi için sertlik, çekme ve TGA analizi yapılmıştır. Malzemelerin molekül yapıları incelendiğinde ise takviye malzemesinin saf polistirenin mikroyapısında anlamlı ölçüde değişikliğe sebep olmadığı görülmüştür. Çekme testlerinde grafen takviyeli kompozitler malzemenin yüzde uzamasını ortalama %1,3 arttırmıştur. Polistiren matris içerisine takviye edilen grafen partikülleri tane sınırları boyunca gerilme yığılmasına neden olduğundan, saf polistirene göre maksimum kopma dayanımı değerinde yaklaşık %30 oranında azalmaya neden olmuştur. Yapılan çalışmalarda grafen yapıda değişime neden olmamakla birlikte birçok özellikte anlamlı oranda iyileşme sağlamıştır.
30 August 2023 in İmalat Teknolojileri ve Uygulamaları
The primary factors of the widespread use of induction melting furnaces are uniform metal and heat distribution due to its mixing features, low alloy losses, excellent temperature and composition control, versatility in processing different materials, the ability to quickly start the process from a cold state when needed, and the absence of air pollution problems. In induction heating, not all sides of the part to be heated receive an equal amount of heat. Only if the part to be heated is of the type that conducts heat very well can all sides of the part be heated close to each other. Induction heating produces high heat on the surface, less on the inner parts, and least on the center of the material. This heating varies depending on the frequency of the current source and the penetration depth. In this study, a model was created in ANSYS numerical analysis program by taking the current, which is one of the electromagnetic and thermal parameters affecting the temperature distribution in the metalic material in induction heating, at different values. In the simulation model created, three-dimensional numerical analysis results of a cylindrical metallic material were obtained. In the simulation program, the power and frequency required for the design of the induction coil and the magnetic permeability, resistivity, heat transfer coefficient of the material and the position of the material in the inductor are determined as boundary conditions. Depending on these variables, the temperature and magnetic field distributions on the material were obtained. In addition to the numerical analysis, a cylindrical metallic material with known properties was placed in a specially manufactured induction coil and the temperature values on the material were measured to verify the numerical analysis. ANSYS modeling results with the same material dimensions, properties, and other parameters used in the experiment, were given and examined in comparison with the experimental results.
In this study, the adhesive wear behavior of different metals lubricated with nanoparticle-modified oils was investigated. Two different metal samples, namely St37 steel and AISI304, were used. As the lubricant, the widely used industrial 10W-40 motor oil was selected and titanium carbide (TiC) and titanium nitride (TiN) nanoparticles were added at concentrations of 1%, 3%, and 5% by weight to improve the tribological properties. The lubricants were homogeneously mixed with the nanoparticles, and the prepared samples were subjected to wear tests using the pin-on-disk method. Tests were conducted under fixed parameters, and subsequently, the worn surfaces were analyzed in detail using SEM, EDS, FTIR, UV spectroscopy and Optical Microscopy techniques. The results demonstrated that the addition of nanoparticles reduced the coefficient of friction and increased wear resistance. Particularly, the addition of 3% TiN and TiC nanoparticles provided lower wear tracks and more homogeneous surface deformation on all metal surfaces. This study presents important findings supporting the potential of nanoparticle-reinforced lubricants to extend the service life and improve the performance of machines in industrial applications.
In this study, polystyrene (PS) and recycled polyethylene terephthalate (R-PET) materials were coated by electrospun polyacrylonitrile/ polyvinyl alcohol (PAN/PVA) and PAN/ polyvinylidene fluoride (PVDF) nanofibers produced by electrospinning method to produce new polymer composite materials. Nanofibers were characterized by SEM, FT-IR and XRD confirmed the formation of PAN/PVA and PAN/PVDF electrospun nanofibers and their beadless and ordered morphology with an average diameter of 188.95±17.12 and 263.44±45.46 nm, respectively. The effect of nanofibrous coating on the tensile properties and hardness properties of the PS and R-PET composite materials obtained by plastic injection method was investigated. PS and R-PET samples were coated with PAN/PVA and PAN/PVDF nanofibers produced for 1h and 2h and these samples were compared for their mechanical properties. In terms of tensile properties, among the PS and R-PET samples, the PAN/PVDF-coated R-PET composite showed the highest tensile strength value of 22.66 MPa and the highest elongation value of 8.49%. The results showed that after nanofibrous coating on PS and R-PET elastic modulus, tensile strength, and elongation at break properties of all samples enhanced. The analysis of hardness revealed an enhancement after nanofibrous coating for R-PET samples while relatively low changes in hardness values were determined for PS composites because of the rigid nature of PS.