The paper presents a novel small-footprint varactor diode-based reconfigurable reflectarray (RRA) design and investigates its power reflection efficiency theoretically and experimentally in a real-life indoor environment. The surface is designed to operate at 865.5 MHz and is intended for simultaneous use with other wireless power transfer (WPT) efficiency-improving techniques that have been recently reported in the literature. To the best of the authors’ knowledge, no RRA intended to improve the performance of antenna-based WPT systems operating in the sub-GHz range has been designed and studied both theoretically and experimentally so far. The proposed RRA is a two-layer structure. The top layer contains electronically tunable phase shifters for the local phase control of an incoming electromagnetic wave, while the other one is fully covered by metal to reduce the phase shifter size and RRA’s backscattering. Each phase shifter is a pair of diode-loaded 8-shaped metallic patches. Extensive numerical studies are conducted to ascertain a suitable set of RRA unit cell parameters that ensure both adequate phase agility and reflection uniformity for a given varactor parameter. The RRA design parameter finding procedure followed in this paper comprises several steps. First, the phase and amplitude responses of a virtual infinite double periodic RRA are computed using full-wave solver Ansys HFSS. Once the design parameters are found for a given set of physical constraints, the phase curve of the corresponding finite array is retrieved to estimate the side lobe level due to the finiteness of the RRA aperture. Then, a diode reactance combination is found for several different RRA reflection angles, and the corresponding RRA radiation pattern is computed. The numerical results show that the side lobe level and the deviation of the peak reflected power angles from the desired ones are more sensitive to the reflection coefficient magnitude uniformity than to the phase agility. Furthermore, it is found that for scanning angles less than 50°, satisfactory reflection efficiency can be achieved by using the classical reactance profile synthesis approach employing the generalized geometrical optics (GGO) approximation, which is in accord with the findings of other studies. Additionally, for large reflection angles, an alternative synthesis approach relying on the Floquet mode amplitude optimization is utilized to verify the maximum achievable efficiency of the proposed RRA at large angles. A prototype consisting of 36 elements is fabricated and measured to verify the proposed reflectarray design experimentally. The initial diode voltage combination is found by applying the GGO-based phase profile synthesis method to the experimentally obtained phase curve. Then, the voltage combination is optimized in real time based on power measurement. Finally, the radiation pattern of the prototype is acquired using a pair of identical 4-director printed Yagi antennas with a gain of 9.17 dBi and compared with the simulated. The calculated results are consistent with the measured ones. However, some discrepancies attributed to the adverse effects of biasing lines are observed.
Simple memristive circuits are attractive chaos sources for secure communication, random-number generation, and chaotic sensing. Reliable operation, however, requires knowing where in parameter space the chaos persists and where periodic windows or coexisting attractors make it fragile. This paper constructs an operating map for an improved memristive diode-bridge band-pass-filter circuit in its two accessible tuning parameters, set by the filter capacitance and the feedback resistance ratio. Two-parameter bifurcation maps and Lyapunov exponent fields give the global layout of the plane; numerical continuation traces the stable and unstable periodic-orbit branches that organise it; and phase portraits, power spectra, component-level SPICE simulation, and prototype measurements characterise representative regimes. The plane separates into broad chaotic regions, higher-period windows, a period-adding window, and a multistability zone. A chaotic interval is reported as robust chaos only when the tracked periodic branches are all unstable, the Lyapunov exponent is positive throughout, and initial-condition scans detect no coexisting attractor; the continuation shows the same period-doubling mechanism bounding the chaotic regions in both parameters. Mapping the dimensionless results to component values yields design guidance for reaching candidate robust-chaos regions and avoiding fragile and multistable zones, including a hardware-confirmed limit on inductor loss beyond which the chaotic band collapses.
The use of chaotic sequences for secure data transmission offers a promising means of protecting information against eavesdropping attacks. Unlike the conventional approach that relies on dedicated chaos oscillators, this study explores the feasibility of utilizing switching power supplies-already integrated into IoT devices for power delivery-as built-in chaos generators, eliminating the need for additional circuitry. This approach has the potential to reduce both cost and system complexity in chaos-based secure IoT communication systems. SPICE simulations are employed to examine the feasibility of synchronizing buck converters via a chaotic drive signal implemented in the feedback loop, as well as to evaluate synchronization performance under parameter deviations. The results show that two buck converters can achieve synchronization with a high correlation coefficient $(>0.9)$ using a chaotic drive signal, while still maintaining the desired output voltage level.
The paper is devoted to forming a power-carrying signal for RF wireless power transfer. The approach takes into account the limitation on power level at a particular frequency. The research presents an algorithm for the signal to be transferred to match the propagation channel. The approach is based on experimental estimates of the wireless channel and the formation of the appropriate signal based on the measurement results. The paper gives the theoretical substantiation of the method and shows its application to wireless power transfer.
This paper describes a numerically efficient method for optimizing the high power transfer efficiency (PTE) of a resonant cavity-based Wireless Power Transfer (WPT) system for the wireless charging of smart clothing. The WPT system under study unitizes a carbon steel closet intended to store smart clothing overnight as a resonant cavity. The WPT system is designed to operate at 865.5 MHz; however, the operating frequency can be adjusted over a wide range. The main reason behind choosing a resonant cavity-based WPT system is that it has several advantages over the competitive WPT methods. Specifically, in contrast to its Far-field Power Transfer (FPT) and Inductive Power Transfer (IPT) counterparts, resonant cavity-based WPTs do not exhibit path loss and significant PTE sensitivity to the distance between the Tx and Rx coils and misalignment, respectively. The non-uniformity of the fields within the closet is addressed by using an optimized Yagi-like transmitting antenna with an additional element affecting the waveguide mode phases. The changes in the mode phases increase the volume inside the cavity, where the PTE values are higher than 50% (the high PTE region). In the present study, the model decomposition method is adapted to substantially accelerate the process of finding the optimal WPT system parameters. Additionally, the decomposition method explains the mechanism responsible for extending the high PTE region. The generalized scattering matrices are computed using the full-wave simulator Ansys HFSS for three sub-models. Then, the calculated S matrices are combined to evaluate the system’s PTE. The decomposition method is validated against full-wave simulations of the original WPT system’s model for several different parameter value combinations. The simulated results obtained for a sub-optimal model are experimentally verified by measuring the PTE of a real-life closet-based WPT system. The measured and calculated results are found to be in close agreement with the maximum measured PTE, as high as 60%.
The paper presents an experimental study on a reconfigurable reflectarray (RRA) design suitable for wireless power transfer (WPT) in the sub-GHz range. The RRA’s capability to redirect the power of the incident wave enables one to deploy a self-adaptable power transfer channel to reduce the effect of path loss on the overall WPT system’s power transfer efficiency. The RRA under study employs varactor diode-loaded metal patches acting as voltage-controlled resonant phase shifters. An RRA prototype comprising 36 geometrically identical phase shifters, each formed by a pair of 8-shaped metallic patches, was fabricated. The metal patches are coupled via varactor diodes to achieve local RRA phase profile alteration by varying diode bias voltages. The phase shifters are printed on several standard FR-4 PCBs, reducing manufacturing costs, which is of primary importance due to their relatively large footprint. The developed RRA can be seamlessly integrated with other WPT-enhancing techniques, such as the multi-hop node technique recently proposed by the authors. To verify the feasibility of the developed RRA, the received power is measured at different angles and for different RRA configurations (desired reflection angles). Each configuration represents a set of varactor diode bias voltages generated to achieve a phase profile, ensuring the power reflection in a desired direction away from the RRA surface. The measured received power is compared with that reflected from a large flat metallic sheet, utilized as a reference reflector, to evaluate the RRA reflection efficiency. The obtained results show that the RRA ensures a reasonably high reflection efficiency. In all the cases examined, the RRA outperforms the metallic sheet in terms of the amount of received power. The reflected energy from the RRA can be used to charge low-power sensor nodes remotely.