Graphitic carbons’ unique attributes have attracted worldwide interest towards their development and application. Carbon pyrolysis is a widespread method for synthesizing carbon materials. However, our understanding of the factors that cause differences in graphitization of various pyrolyzed carbon precursors is inadequate. We demonstrate how electro-mechanical aspects of the synthesis process influence molecular alignment in a polymer precursor to enhance its graphitization. Electrohydrodynamic forces are applied via electrospinning to unwind and orient the molecular chains of a non-graphitizing carbon precursor, polyacrylonitrile. Subsequently, exerting mechanical stresses further enhances the molecular alignment of the polymer chains during the formative crosslinking phase. The stabilized polymer precursor is then pyrolyzed at 1000 °C and characterized to evaluate its graphitization. The final carbon exhibits a uniformly graphitized structure, abundant in edge planes, which translates into its electrochemical kinetics. The results highlight the significance of physical synthesis conditions in defining the structure and properties of pyrolytic carbons.
A simple and inexpensive alternative to high-power lasers for the direct fabrication of microchannels and rapid prototyping of poly-dimethylsiloxane (PDMS) is presented. By focusing the infrared laser beam of a commercial, low-power CD-DVD unit on absorbing carbon micro-cluster additives, highly localized PDMS combustion can be used to etch the polymer, which is otherwise transparent at such wavelengths. Thanks to a precise and automated control of laser conditions, laser-induced incandescence is originated at the material surface and produces high-resolution micropatterns that present properties normally induced with lasers of much greater energies in PDMS: formation of in situ nanodomains, local fluorescence and waveguide patterns. An extensive study of the phenomenon and its performance for PDMS microfabrication are presented.
1 January 2008 in 2008 IEEE 21st International Conference on Micro Electro Mechanical Systems
The sensitivity loss, commonly presented in micro gyroscopes based on harmonic oscillators [1], is overcome by using parametric resonance as an actuation mechanism. This operation has been analytically studied in IEEE- Sensors'05 [2] and preliminary dynamical characterization and experimental setup has been presented in IDETC/CIE- ASME'07 [3]. The device is fabricated using SOI process and in this paper we report complete rate table characterization including off-axis isolation, drift, hysteresis and noise of the micro gyroscope with an additional amplification stage.
A feasibility analysis of using parametric amplifi- cation in order to improve the performance of a micromachined rate gyroscope is presented. The actuation is based on variable force actuators that depend on the force-time variation relation, thus the nonlinear Mathieu equation governs the driving motion. We demonstrated by numerical simulations that in a parametric amplified system with linear mechanical stiffness there exist a flattened region that can be used as the operation region of a 2- DOF microgyroscope. In this way the system is able to achieve a wider bandwidth of operation without sacrificing the sense mode gain: a robust micro sensor that is less sensitive to parameter variations.
11 January 2019 in Journal of Micromechanics and Microengineering
Development of carbon based micro electromechanical systems (C-MEMS) has enabled the fabrication of durable, low cost and biocompatible micro devices for specific applications. Thermochemical decomposition of SU-8 (a common photoresist) is often used to fabricate C-MEMS. However, this technique has yielded unreliable results when fabrication on transparent substrates is required due to cracking and detachment of the produced carbon micro structures. We present a methodology for the fabrication of photopatterned carbon films based on SU-8 deposited on transparent fused silica substrates. Specifically, we developed and implemented this methodology for carbon microstructure fabrication derived from SU-8 2035 and SU-8 3035. It was found that SU-8 3035 derived carbon microstructures were crack free and adhered well to the substrate, while SU-8 2035 resulted in fractured and detached carbon microstructures. In addition, we characterized the produced SU-8 3035 derived carbon by measuring its electrical resistivity (1.412 ± 0.011 mΩ m), inter-structure electrical resistance, contact angle (35.7° ± 6.0°), Raman spectrum and adhesion strength to the substrate. In brief, even though SU-8 2035 and SU-8 3035 are useful materials for C-MEMS fabrication, we found that SU-8 3035 is more suitable for the fabrication of crack free and adherent carbon microstructures on transparent fused silica substrates.