Leonidas Karavias

Mr. Leonidas Karavias

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 November 2023 in Metals
Verified
Journal Article
Open access
PDF file
LGLeonidas Gargalis
Leonidas Gargalis
LKLeonidas Karavias
Leonidas Karavias
JGJoachim Seland Seland Graff
Joachim Seland Seland Graff
SDSpyridon Diplas
Spyridon Diplas
Elias KoumoulosElias Koumoulos
Elias Koumoulos
EKEvangelia K. Karaxi
Evangelia K. Karaxi
The aim of this paper was to compare duplex (DSS) and super duplex stainless steel processed by laser powder bed fusion (LPBF) based on the process parameters and microstructure–nanomechanical property relationships. Each alloy was investigated with respect to its feedstock powder characteristics. Optimum process parameters including scanning speed, laser power, beam diameter, laser energy density, and layer thickness were defined for each alloy, and near-fully dense parts (>99.9%) were produced. Microstructural analysis was performed via optical (OM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The samples were subjected to stress relief and high-temperature annealing. EBSD revealed the crystallographic orientation and quantified the phases in the as-built and annealed sample conditions. The as-built samples revealed a fully ferritic microstructure with a small amount of grain boundary austenite in the SDSS microstructure. High-temperature solution annealing resulted in the desired duplex microstructure for both alloys. There were no secondary phases present in the microstructure after both heat treatments. Nanoindentation generated nanomechanical (modulus) mapping grids and quantified the nanomechanical (both hardness and modulus) response; plasticity and stress relief were also assessed in all three conditions (as-built, stress-relieved, and annealed) in both DSS and SDSS. Austenite formation in the annealed condition contributed to lower hardness levels (~4.3–4.8 Gpa) and higher plastic deformation compared to the as-built (~5.7–6.3 Gpa) and stress-relieved conditions (~4.8–5.8 Gpa) for both alloys. SDSS featured a ~60% austenite volume fraction in its annealed and quenched microstructure, attributed to its higher nickel and nitrogen contents compared to DSS, which exhibited a ~30% austenite volume fraction.

1 September 2023 in Metals
Verified
Journal Article
Open access
PDF file
LGLeonidas Gargalis
Leonidas Gargalis
LKLeonidas Karavias
Leonidas Karavias
JGJoachim Seland Seland Graff
Joachim Seland Seland Graff
SDSpyridon Diplas
Spyridon Diplas
Elias KoumoulosElias Koumoulos
Elias Koumoulos
EKEvangelia K. Karaxi
Evangelia K. Karaxi
Additive manufacturing of Duplex Stainless Steels (DSS) and Super Duplex Stainless Steels (SDSS) has been successfully demonstrated using LPBF in recent years, however, both alloys feature an almost fully ferritic microstructure in the as-built condition due to the fast cooling rates associated with the Laser Powder Bed Fusion (LPBF) process. Blends of DSS and SDSS powders were formulated with austenitic stainless-steel 316L powder, aiming to achieve increased austenite formation during in the LPBF as-built condition to potentially minimize the post heat treatments (solution annealing and quenching). Powder characteristics were investigated and process parameters were optimized to produce near fully dense parts. Nanoindentation (NI) tests were conducted to measure, not only the local mechanical properties and correlate them with the as-built microstructure, but also to gain a deeper understanding in the deformation behavior of individual phases that cannot be studied directly by macroscopic tensile tests. Scanning Electron Microscopy (SEM) and Electron Backscatter Diffraction (EBSD) were employed for microstructural analysis and phase quantification. The microstructural analysis and EBSD phase maps revealed an increase in austenite in the as-built microstructures. Blend 1 resulted in a duplex microstructure consisting of 10% austenite at the XY plane and 20% austenite at the XZ plane. The austenite content increased with increasing proportion of 316L stainless steel in the powder blends. The DSS blend required a much higher volumetric energy density for the fabrication of near fully dense parts. This imposed a slower solidification and a higher melt pool homogeneity, allowing for adequate diffusion of the austenite stabilizing elements. The presented workflow and findings from this study provide valuable insights into powder mixing for the development of custom alloys for rapid material screening in LPBF.

22 July 2024 in Metals
Verified
Journal Article
Open access
PDF file
LKLeonidas Karavias
Leonidas Karavias
LGLeonidas Gargalis
Leonidas Gargalis
JGJoachim Seland Seland Graff
Joachim Seland Seland Graff
MJMarius Johansen
Marius Johansen
SDSpyridon Diplas
Spyridon Diplas
EKEvaggelia K. Karaxi
Evaggelia K. Karaxi
Additive manufacturing of duplex (DSS) and super duplex stainless steel (SDSS) has been successfully demonstrated using laser powder bed fusion (LPBF) in recent years. Owing to the high cooling rates, as-built LPBF-processed DSS and SDSS exhibit close to 100% ferritic microstructures and require heat treatment at 1000–1300 °C to obtain the desired duplex microstructure. In this work, the mechanical properties of DSS and SDSS processed via LPBF were investigated in three building directions (vertical, horizontal, diagonal) and three processing conditions (as-built, stress-relieved, annealed, and quenched) using uniaxial tensile testing. As-built samples exhibited tensile and yield strength greater than 1000 MPa accompanied by less than 20% elongation at break. In comparison, the water-quenched samples and samples annealed at 1100 °C exhibited elongation at break greater than 34% with yield and tensile strength values less than 950 MPa. Stress relief annealing at 300 °C had a negligible impact on the mechanical properties. Austenite formation upon high-temperature annealing restored the reduced ductility of the as-built samples. The as-built and stress-relieved SDSS showed the highest yield and tensile strength values in the horizontal build direction, reaching up to ≈1400 and ≈1500 MPa (for SDSS), respectively, as compared to the vertical and diagonal directions. Fractographic investigation after tensile testing revealed predominantly a quasi-ductile failure mechanism, showing fine size dimple formation and cleavage facets in the as-built state and a fully ductile fracture in the annealed and quenched conditions. The findings in this study demonstrate the mechanical anisotropy of DSS and SDSS along three different build orientations, 0°, 45°, 90°, and three post-processing conditions.

15 May 2025 in Toxics
Verified
Journal Article
Open access
PDF file
NSNikoletta Sargioti
Nikoletta Sargioti
LKLeonidas Karavias
Leonidas Karavias
LGLeonidas Gargalis
Leonidas Gargalis
AKAnna Karatza
Anna Karatza
Elias KoumoulosElias Koumoulos
Elias Koumoulos
EKEvangelia K. Karaxi
Evangelia K. Karaxi
This study investigates the physicochemical and toxicological properties of Scalmalloy powder emissions generated during Laser Powder Bed Fusion (LPBF), focusing on the impact of particle morphology, oxidation, and size distribution on biological responses. Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) analyses revealed significant variations in particle characteristics, with the highest oxidation levels and irregular morphologies observed in exhaust-derived powders. In vitro cytotoxicity evaluations using A549 lung epithelial cells showed significant reductions in cell viability (~60 to 69%) and increased oxidative stress (p < 0.05) upon exposure to virgin sieved (85%). Indirect exposure through media incubation resulted in minimal cytotoxicity, suggesting that metal dissolution plays a limited role in toxicity under the studied conditions. The findings highlight the influence of particle morphology and oxidation on cytotoxic responses and underscore the need for controlled powder handling to mitigate occupational exposure risks in LPBF environments.

8 August 2025 in Metals
Verified
Journal Article
Open access
PDF file
AAAikaterini Argyrou
Aikaterini Argyrou
LGLeonidas Gargalis
Leonidas Gargalis
LKLeonidas Karavias
Leonidas Karavias
EKEvangelia K. Karaxi
Evangelia K. Karaxi
Elias KoumoulosElias Koumoulos
Elias Koumoulos
This study investigates the combined effects of build planes and heat treatments on the micro- and nanoscale mechanical properties of additively manufactured AlSi10Mg alloy. The hardness and elastic modulus were examined across two principal planes, XY and XZ, under three conditions: as-built (AB), after solution annealing followed by water quenching (SA), and artificially aged after solution annealing (SA&AA). The results reveal that hardness is significantly affected by heat treatment, decreasing after SA and partially recovering upon subsequent artificial aging (SA&AA), while remaining largely unaffected by build planes, with average values differing by less than 2%. In contrast, the elastic modulus demonstrates a clear anisotropy, correlated with the microstructural changes from both additive manufacturing and thermal post-processing. The XY plane initially shows a modulus up to 29% higher than the XZ plane. However, after aging, the values of both planes converge to similar levels. While average values suggest general trends, localized measurements reveal notable spatial heterogeneity in both the hardness and elastic modulus—particularly after thermal treatments—arising from microstructural evolutions. These findings highlight the complex interplay between orientation and thermal history, underscoring that the mechanical performance of AlSi10Mg is governed by the synergistic effects that influence anisotropy and local mechanical behavior.

12 March 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
AAAikaterini Argyrou
Aikaterini Argyrou
LGLeonidas Gargalis
Leonidas Gargalis
LKLeonidas Karavias
Leonidas Karavias
EKEvangelia K. Karaxi
Evangelia K. Karaxi
Elias KoumoulosElias Koumoulos
Elias Koumoulos
Laser Powder Bed Fusion (LPBF)-processed AlSi10Mg produces highly heterogeneous microstructures, where fine α-Al cells, Si-rich networks, and melt-pool boundaries govern local mechanical behavior. Nanoindentation has emerged as a key tool for probing these variations, yet systematic understanding of the links between processing parameters, microstructure, and nano-mechanical response remains limited. This critical review examines how laser processing parameters influence local mechanical response through their impact on microstructural features. Key challenges in interpreting nanoindentation are highlighted, alongside inconsistencies in experimental protocols and reporting practices that hinder cross-study comparisons. Beyond summarizing existing findings, underexplored aspects of nanoindentation in LPBF AlSi10Mg are identified, including spatially correlated microstructure-mechanical mapping, depth-resolved measurements, and integration with advanced characterization and data-driven approaches. By synthesizing current knowledge and clarifying methodological constraints, this review positions nanoindentation not merely as a descriptive tool, but as a mechanistically informed approach for linking processing conditions, microstructural heterogeneity, and local mechanical response. These insights aim to support more rigorous interpretation of small-scale mechanical data and to guide future studies toward predictive understanding and rational process optimization in additively manufactured aluminum alloys.