There are various methods to evaluate the forming limit of a sheet, and these criteria can be classified as position-dependent, time-dependent, and position-time dependent according to the basis of judgment. However, these criteria have a single function and can only find the forming limit of the sheet and cannot determine the strain distribution, strain change, or fracture location during the sheet forming process. This paper introduces a time–location-dependent method, i.e., the spatial strain rate method, which is used to detect the onset of necking of a sheet. The spatial strain rate is directly based on the strain and can not only find the forming limit of the sheet but also depict the strain distribution and strain variation during the two phases of the experimental process—distributed instability and concentrated instability—as well as predict the location of sheet fracture. The spatial strain rate of AA5083 aluminum alloy of different widths was analyzed and verified in detail via Nakazima experiments using digital image correlation techniques and compared with the guidelines published in the literature in recent years.

Sodium-ion batteries are renowned for their abundant reserves, cost-efficiency, safety, and eco-friendliness and are prime candidates for large-scale energy storage applications. The development of cathode materials plays a crucial role in shaping both the commercialization path and the ultimate performance capabilities of SIBs. To overcome the intricate synthesis challenges associated with pure-phase sodium-ion cathode materials, this study introduces an innovative and streamlined electrochemical Li⁺/Na⁺ exchange process, successfully fabricating a high-capacity Ni-rich cathode material. This cathode material boasts a remarkable reversible capacity of 180 mAh g⁻¹ at 0.1 C and retains a high-rate capacity of 115 mAh g⁻¹ even at 5 C. Additionally, it exhibits exceptional cycling stability, retaining about 85% of its capacity at 1 C after 50 cycles and still maintaining a capacity greater than 60% after 100 cycles. The Na-NMA85 full cell preserves a discharge capacity of 110 mAh g⁻¹ after 100 cycles, with a capacity retention rate of 80%. This research underscores innovative strategies for designing ion-intercalation-based cathode materials that enhance battery performance, providing fresh perspectives for advancing high-performance battery technologies.

Ni-rich layered oxide LiNi_0.91Co_0.06Al_0.03O₂ (NCA91) with high specific capacity has emerged as a leading cathode candidate for advanced lithium-ion batteries (LIBs). Nevertheless, increase in Ni content triggers structural instability and fast capacity degradation, which severely impedes the practical application of Ni-rich materials. Herein, a comprehensive study is conducted to explore the structural evolution and electrochemical behaviors of NCA91 cathodes with precisely tuned Li/TMs (transition metals) molar ratios spanning from 1.01 to 1.07. Results reveal that the NCA91 electrode with an optimal Li/TMs ratio of 1.03 exhibits outstanding structural integrity, coupled with remarkable cycling durability and rate capability. Specifically, the cathode with Li/TMs = 1.03 retains 88% of its initial capacity after 100 cycles at 1 C, and maintains ~130 mAh g⁻¹ even at 10 C. This work establishes a quantitative structure–composition–performance correlation that offers critical design principles for developing ultrahigh-nickel cathode materials.

A novel fabrication process to connect single-stranded DNA (ssDNA)to a silicon substrate based on a mechano–chemical method is proposed. In this method, the single crystal silicon substrate was mechanically scribed in a diazonium solution of benzoic acid using a diamond tip which formed silicon free radicals. These combined covalently with organic molecules of diazonium benzoic acid contained in the solution to form self-assembled films (SAMs). The SAMs were characterized and analyzed by AFM, X-ray photoelectron spectroscopy and infrared spectroscopy. The results showed that the self-assembled films were covalently connected to the silicon substrate by Si–C. In this way, a nano-level benzoic acid coupling layer was self-assembled on the scribed area of the silicon substrate. The ssDNA was further covalently connected to the silicon surface by the coupling layer. Fluorescence microscopy showed that ssDNA had been connected, and the influence of ssDNA concentration on the fixation effect was studied. The fluorescence brightness gradually increased with the gradual increase in ssDNA concentration from 5 μmol/L to 15 μmol/L, indicating that the fixed amount of ssDNA increased. However, when the concentration of ssDNA increased from 15 μmol/L to 20 μmol/L, the detected fluorescence brightness decreased, indicating that the hybridization amount decreased. The reason may be related to the spatial arrangement of DNA and the electrostatic repulsion between DNA molecules. It was also found that ssDNA junctions on the silicon surface were not very uniform, which was related to many factors, such as the inhomogeneity of the self-assembled coupling layer, the multi-step experimental operation and the pH value of the fixation solution.

This paper analyzes the characteristics and development of the current industrial design education at home and abroad. It combines some of the problems of the current domestic industrial design education, and investigates the problem of industrial design professionals' training direction, curriculum provision and ranks of teachers and so on under the new situation .Then it puts forward some specific K + S training pattern of talented person .

Ti-10wt.%Cu sintered alloy was prepared by apowder metallurgy method to obtain strong antibacterial property. In order to optimize the deformation processing, the hot deformation behaviour of Ti-10wt.%Cu sintered alloy was investigated in this paper. The deformation temperature was set between 800°C to 1000°C and the strain rate was set in a range of 0.008 s⁻¹ to 5s⁻¹. The microstructure of the deformed alloy were observed in order to reveal the effect of the hot deformation process on the microstructure. The results showed that the Ti₂Cu phase distributed homogeneously with the increasing of the deformation temperature and decreased with the increasing of the strain rate. It was concluded that the final optimized deformation process was: a deformation temperature range of 850°C to 950°C, and a strain rate of 0.1s⁻¹ to 0.5s⁻¹.