MOHAMMED ZUBAIRUDDIN

Dr. MOHAMMED ZUBAIRUDDIN

orcid

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2017 in Journal of Manufacturing Processes
Verified
Journal Article
Closed access
MZMOHAMMED ZUBAIRUDDIN
MOHAMMED ZUBAIRUDDIN
SAS.K. Albert
S.K. Albert
MVM. Vasudevan
M. Vasudevan
SMS. Mahadevan
S. Mahadevan
VCV. Chaudhari
V. Chaudhari
VSV.K. Suri
V.K. Suri

12 December 2014 in Journal of Mechanical Science and Technology
Verified
Journal Article
Closed access
PDF file
MZMOHAMMED ZUBAIRUDDIN
MOHAMMED ZUBAIRUDDIN
SAShaju K. Albert
Shaju K. Albert
SMS. Mahadevan
S. Mahadevan
VMVasudevan M
Vasudevan M
VCVilas Chaudhari
Vilas Chaudhari
VSV. K. Suri
V. K. Suri

19 March 2015 in Materials and Manufacturing Processes
Verified
Journal Article
Closed access
MZMOHAMMED ZUBAIRUDDIN
MOHAMMED ZUBAIRUDDIN
SAS. K. Albert
S. K. Albert
VMVasudevan M
Vasudevan M
SMS. Mahadevan
S. Mahadevan
VCV. Chaudhri
V. Chaudhri
VSV. K. Suri
V. K. Suri
Effect of preheat on the thermal cycles, residual stress, and distortion during autogenous GTA welding of Grade P91 steel has been analyzed using FEM. Phase transformation effect on the residual stresses is also analyzed. Thermomechanical analysis has shown that preheat reduced the peak temperatures, cooling rate, and the distortion values. The phase transformation involving martensite during cooling resulted in typical “M” shaped residual stress profile with a reduction in peak tensile residual stress value and a wider distribution of residual stress. There is good agreement between the predicted and measured thermal cycles, residual stresses, and distortion of the P91 steel weld joint.

1 November 2021 in Optik
Verified
Journal Article
Closed access
MZMOHAMMED ZUBAIRUDDIN
MOHAMMED ZUBAIRUDDIN
RKR. Ravi Kumar
R. Ravi Kumar
PCP.K. Chaursaia
P.K. Chaursaia
BABaharin Ali
Baharin Ali

25 March 2025 in Scientific Reports
Verified
Journal Article
Open access
PDF file
MZMOHAMMED ZUBAIRUDDIN
MOHAMMED ZUBAIRUDDIN
MVM. Vasudevan
M. Vasudevan
PDP. K. Das
P. K. Das
MAMohammad Mukhtar Alam
Mohammad Mukhtar Alam
KKK. Suresh Kumar
K. Suresh Kumar
PSPrabhakar S
Prabhakar S
Present research deals with the thermo-mechanical analysis of the butt joint plate and weld pool characteristics of the bead on plates fabricated using A-TIG and conventional TIG process. A square butt joint was welded using P91 steel of 4 mm thickness plates, employing in-house developed oxide flux. Thermal cycles induced during the welding was recorded with thermocouple, and residual stress produced in both plates was measured using the XRD method. It is observed that A-TIG produces less detrimental effects than the conventional TIG. Concentrated heat intensity is observed during the A-TIG with the narrow and deep penetration depth dispersed with lesser heat to base metal than the TIG welded joint. Comparison of bead on plate showed that FZ and HAZ increase to 10% and 34% more widely in the TIG welding process. The maximum stress value in the A-TIG welding process reached up to 471 MPa near the weld bead, whereas in the TIG welding, it was 509 MPa with 8% reduction in stress value. Reduction in distortion is also observed in the case of A-TIG, with a 36% reduction in values. Distortion in the weld plate is also compared with predicted results. FEM-based simulation is performed for both processes using the SYSWELD. Combined double ellipsoidal with conical heat source model was used for A-TIG and double ellipsoidal model was used for conventional TIG welding. Based on the comparison of the results, it can be concluded that the predicted results are approximately near to experimental measured values for thermal and mechanical results. It is observed that A-TIG plate induced less distortion and stress than the conventional TIG process.

5 August 2019 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
APA. R. Pavan
A. R. Pavan
BAB. Arivazhagan
B. Arivazhagan
MZMOHAMMED ZUBAIRUDDIN
MOHAMMED ZUBAIRUDDIN
SMS. Mahadevan
S. Mahadevan
VMVasudevan M
Vasudevan M